541323

Acoustica Mixcraft-4 Manual

40
Zoom out
Zoom in
Previous page
1/93
Next page
Choose Adjust Pitch By from the drop down list on the Sound Details Tab.
This allows you to change the pitch by semitones. You can type in a partial amount such as 1.26 semitones or use
the drop down or spin arrows to adjust by a whole semitone or 1/10th of a semitone. You might use this option to
fix a slightly off key vocal performance or transpose a sound into a key you are more familiar with.
Adjust To Project Key
Click here for more on adjusting a sound's key.
Transposing Virtual Instrument Clips
You can transpose a Virtual Instrument Clip by clicking on the Sound Details tab on the bottom of the window.
Click on the drop down entitled Adjust To Project Key and choose Transpose By.
Then either type in or select the number of half steps that you'd like to transpose the clip by.
Virtual Instrument clips can be transposed without audio degradation because each time they are played the
synthesizer recreates the sound from the MIDI data.
Adjusting The Sound's Key
You can change a sound's key by clicking the Sound Details Tab on the bottom of the window. Each sound can be
in one of the following modes: Adjust To Project Key, Adjust Pitch By, Transpose By (Virtual Instrument clips only)
or Do Not Fix Pitch. (Audio clips only) Select the drop down to change the mode to Adjust to Project Key.
Adjust To Project Key
If in this mode, Mixcraft will adjust the pitch of the sound based on the difference between the project's key and the
sound's key. For example, if the project key was F# and the sound's key was F, it would adjust the pitch of the
sound up by one semitone so that it was in tune with F# instead of F.
However, you can have more than one key change in a project. A sound in Adjust To Project Key mode will adjust
to the correct # of half steps in order to play in the correct key based on the most recent key change. To continue
the example, if your sound was in F and you had two key changes to A and then G, it would correspond to shifting
the pitch of your sound by four semitones up to A and then by two semitones up to G.
The software adjusts the pitch by the shortest distance between two keys. For example, if the project key was G
and the sound's key was F, it will adjust it by +2 semitones, instead of -10 semitones.
Changing The Key Of A Sound
A
ssuming that the key of the sound is correct, you can change the key of a sound by adding markers with key
changes and/or by changing the project's key. You do not need to change the key of the sound on the Sound
Details Tab, but, instead, you should change the project key or add key change markers! In short, if you want to
change the key of a sound, change the project key! Changing the key of a sound should only be done if the
detected key is wrong!
Changing The Detected Key Of A Sound
You must be in
A
djust To Project Key mode to change the detected key of a sound.
Page 40 of 93Mixcraft 4
2/7/2008file://C:\acoustica\mixcraft\hel
p
\flat-manual\mixcraft.htm
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acoustica Mixcraft-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acoustica Mixcraft-4 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info