616307

AceSee AS-0410 Manual

3
Zoom out
Zoom in
Previous page
1/26
Next page
H.264 NETWORK Embedded DVR
User Manual
Plastic shell DVR
Thank you for purchase our product. Please read this user manual carefully to ensure
that you can use the device correctly and safely.
Attentions:
◆The DVR should be installed in a well-ventilated place，keep suitable space from
ground ,benefit for machine cooling，Be sure not to block its air vent.，keep away from heat
sources and high temperaturea environment。
◆Please keep the level installation of this product.should be avoid install at violently
shaking place（such as the back of car、motor above、high and rough luggage-rake）.
◆For avoid short circuit cause fire or other damage，when wash the car please
prevent DVR(include camera and other parts) touch water and wet, the machine don’t have
waterproof.
◆The equipment consists of Precision Parts, please do not try to disassemble
or adjust any parts, if need maintenance, please contact the distributer or customer
service.
◆Please select the hard disk which commended by the manufacturers,suit
the DVR work requirement, to meet a long time largeamount of data read and write
requests, please purchase from the formal channels to ensure the hard disk quality .
◆This product can’t bear heavy weight, please do not place heavy object
or multi-layer laminated on the product .
Disclaimer:
The Company is do the best to make the contect correct and complete
during the preparation of this manual, if has any errors or omissions without any liability, the
company reserves the right to change any hardware and software mentioned inthis manual at
any time, and without explain beforehand. Thank you for choosing our products, please read
this manual carefully before use. Due to not according to the specified operating losses,
company will not assume any financial liability and legal responsibility.
3
CONTENT
CONTENT.............................................................................................................3
1. Product Introduction
........................................................................................
3
1.1 Summary
................................................................................................
3
1.2 Main Functions...................................................................................... 4
1.3 Rear panel diagram.............................................................................. 4
2. Basic function operation
.................................................................................
6
2.1 On/off Switching navigation
.................................................................
6
2.2 Login....................................................................................................... 6
2.3 Main menu setup guide
........................................................................
7
2.4 Configuration management................................................................. 9
2.5 Data retrieval....................................................................................... 21
2.6 Backup
..................................................................................................
24
2.7 Check information
...............................................................................
24
2.8 Disk management...............................................................................25
2.9 Upgrade................................................................................................26
2.10 Logoff
..................................................................................................
26
2.11 System shut down
............................................................................
26
4
1. Product Introduction
1.1 Summary
This device is a digital monitoring and recording product specially designed for the
security field. It adopts standalone processor and standalone Linux operating system.
The device combines with the latest technologies in the IT field, such as video and
audio compression/decompression, large capacity HDD record, TCP/IP network etc.. The
code is embedded in the FLASH chip, which makes the system running more steadily. This
device has both features of digital video and audio recording(DVR) and digital video and
audio server(DVS). It can not only work locally and independently but also compose of a
powerful security monitoring net with networking. With the use of professional network
video surveillance platform (network) software, it can fully reflect its strong networking and
remote monitoring capability.
It can be used for the security protection in the fields of banking, telecommunications,
electronic power, justice, traffic, residential, factory, warehouse, water conservancy facilities
and other areas and departments.
1.2 Main Functions
Real-time Monitoring
It is with analog video output port, VGA port and HDMI port. It can realize the monitoring
function through the monitor or display. It supports simultaneous TV ，VGA and HDMI
output.
Storage Function
It adopts special format to save data which cannot be tampered with and will be secured
Compression Method
It supports multi-channel audio and video signal. Each channel of audio and video signal is
compressed in real time by independent hardware. The sound and image keep stabilized
synchronization.
Backup Function
It backups through USB port(such as common U disk, mobile hard disk, SATA Combo etc.)
The client computer can download and backup the files on the hard disk via the internet
Video Playback Function
Each channel can realize independent and real-time recording, while retrieval, reverse play,
network monitoring, video search and download etc. can realize simultaneously.Multiple
playback modes: slow forward, fast forward, reverse play and frame-by-frame play.
When playing back the video, the exact time of the event can be displayed.
Network Operation Function
Through the internet, you can realize remote and real-time monitoring, remote video
search and playback, and remote PTZ control.
Communication Port
With RS485 port and PTZ control.
With standard Ethernet port, realizing network remote control function
Intelligent Operation
Mouse operation function.For the same settings on the menu, you can copy and paste
quickly.check equipment and accessories..
When you receive the product, please check the accessories are complete or not.
DVR accessories generally include: mouse, power lines and data lines.
5
1.3 Rear panel diagram
Statement(Pictures will be subject to the actual:): pic:
the rear panel interface, button layout and type, real product shall prevail. ，below rear
panel picture may be different with the actual panel.
Connectors on Rear Panel：
Item Physical connector Connector description
1 VIDEO IN
For connecting digtial video signal input
(BNC)
2 CVBS
Video output for connecting TV or monitor
(BNC)
3 AUDIO OUT For connecting audio signal output
4 VGA For connecting VGA monitor
5 AUDIO IN For connecting Intercom equipment
6 RJ45 For connecting Ethernet
7 USB2.0 For connecting mouse or USB disk
8 Power input DC 12V/2A
6
2. Basic function operation
2.1 On/off Switching navigation
2.1.1 Start
Before start，Please ensure all parts connected well！
Power on
Equipment start，POWER indicator light is red.
2.1.2 Power off
User can power off the device by using remote controller、keyboard and mouse.
2.1.3 Disconnect the power by keyboard and mouse:
Step1: enter into Menu, then select “System Shut Down” icon, the Shut down window
will appear
Step2: click OK, the unit will power off after a while.
Step3: disconnect the power
2.2 Login
Equipment start ,【POWER】indicator light bright. initial password is blank. After
equipment start press 【MENU】key on panel or press right key on mouse, trun to login
interface as below:
Pic2-1 User login
After Input matching user name and password,you can enter system to setup and
operation.
Live preview interface:
7
Live playback
Click Playbutton to playback the record enter fast record playback: as lelow
picture: User can do concrete operation by click the buttons on screen.
2.3 Main menu setup guide
Menu bar: Click right mouse or press ESC button on the front panel, the control bar
will display on the bottom of the screen, refer to pic2-2
Pic2-2 Menu bar
Click the icon near Screen mode , appear channel choose frame as below
Icon
Sign
description
Recording
Manual
record
Motion
detectio
n state
Alarm
state
Timing
recording
state
8
Pic2-3 Channel choose
user could choose 1 channels from 1-4 to show live video.click to save.
Click function menu ，will show dialogue frame as Pic 2-4;
Pic 2-4 Mian function
Click“Config”，display syswindows as pic2-5:
Pic 2-5 Configuration management”
Press MENU button on the front panel or the same button on remote control,
also cuold display the same window.
9
2.4 Configuration management
Configuration Management contains nine sub-menu: basic configuration,
on-site configuration, video configuration, recording plan, alarm configuration, network
configuration, user management, PTZ configuration and advanced configuration.
2.4.1 Basic configuration
Click“Basic configuration”，show window as pic2-6, The basic configuration
contains two sub-menu: system date and time
1) system
Pic 2-6 System
In this interface user can setup the device name, device ID, video format , Video
Output and language, Screensaver and so on. The definitions for every parameters display
as below:
Device name: It may display on the client end or CMS that help user to recognize the
device remotely.
Device number: Corresponding with the remote control number
Video format: two modes: PAL and NTSC. User can select the video format according
to that of camera.
Password check: Enable this option. user needs to input user name and password
can do corresponding operations with the relevant right in system configuration.
Show system time：choose display time in liveor not
Video output: the resolution of live display interface, range from: VGA800*600,
VGA1024*768, VGA1280*1024,HDMI 1080P
Language: setup the menu language:English, Italian,Greek, Russian, Polish, Portuguese,
Turkish, Hungrain,Spanish, French, German Japanese,Slonakia,Vietnam, Simple Chinese,
Traditional Chinese.
Click the "Default" button, the system restore the default things ;
Click the "Apply" button will save the above settings; click the "Exit"button to exit the
current interface ,Tip to change the menu language and video output, the device will restart.
10
2 ) Time & date
Pic 2-7 Time & date
Set the date format, time format time zone at the date and time "interface;
Note: Click the "Default" button, the system restore the default settings;
Click the "Apply" button will save the above settings;
Click the "Exit"button to exit the current interface.
2.4.2 Live configuration
Click“Live configuration”，enter window as pic2-8
Live configuration includes two submenus : live and mask
2.4.2.1 Live configuration
Pic 2-8 Live configuration
Note: Click Camera Name to see a soft keyboard. User can choose
different character format to input.
11
Tick off camera name and click “Setup” button to display a window as below：
Pic 2-9 Live-color adjustment
In this interface, user can adjust brightness, hue, saturation and contrast in live; click
“Default” button to resort default setting, click “OK” button to save the setting.user can setup
all channels with same parameters, please tick off “all” and then do relevant setup.
2.4.2.2 Mask
Private mask. User can setup private mask area on the live image picture,
Pic 2-10Mask
Setup mask area: click Setting button, enter into live image to press left mouse and
drag mouse to set mask area, refer to below picture. Click Apply button to save the setting.；
Delete mask area: select a certain mask area, click left mouse to delete that mask
area, click Apply button to save the setting.
Live image mask area
12
2.4.3 Record configuration
Click“Record configuration”，enter window as pic2-11：
Record configuration includes four sub menus: start, record bit rate, Character
overlay. recycle record.
2.4.3.1 Start
Pic 2-11 Start
Tick off record channel, channel audio.
User can setup all channels with same parameters, tick off “All”, then to do relevant
setup.
Click “Default” button to resort default setting; click “Apply” button to save the setting;
click “Exit” button to exit current interface.
Video parameters instruction
Parameter Meaning
Enable Every channel video record switch
audio
Start use the channel record audio
13
2.4.3.2 Record bit rate
Pic 2-12 Record bit rate
Setup rate, resolution, quality, encode and max bit stream
User can setup all channels with same parameters, tick off “All”, then to do relevant
setup.
Click “Default” button to resort default setting; click “Apply” button to save the setting;
click “Exit” button to exit current interface.
2.4.3.3 Record stream introduce
Parameter Meaning
Fps Range from 1-30（NTSC）1-25(PAL)
Resolution Support 960H、D1、CIF
Quality
Coding Support CBR and VBR
Max bitrate
14
Stamp：User can overlap the channel name and time stamp on video
.
Pic 2-13 Character overlay
Tick off camera name, time stamp; click Setting button, and then user can use cursor
to drag the camera name and time stamp in random positions. Please refer to below Figures
User can also setup all channels with same parameters.
Click “Default” button to resort default setting; click “Apply” button to save the setting; click
“Exit” button to exit current interface
2.4.3.4 Recycle record
Tick off recycle record to enable the recycle record function. It will cover the earlier
recorded files and keep recoding when HDD is full; if disenabled, it will stop recording when
HDD is full. Note: general the image quality, frame rate and resolution parameters setting
higher, the more take up disk space.
Click “Default” button to resort default setting; click “Apply” button to save the setting;
click “Exit” button to exit current interface.
2.4.4 Schedule configuration
Schedule configuration includes two sub menus: schedule、motion and sensor.
2.4.4.1 Schedule
The volume means the seven days of a week from Monday to Sunday; the row
means 24 hours of a day. Click the grid to do relevant setup. Blue means checked area,
gray means unchecked area.
Pic 2-14 Schedule
Copy：User can apply the schedule setting of certain channel to other or all channels.
Just only select channel and click “Copy” button.
15
Click “Default” button to resort default setting; click “Apply” button to save the setting;
click “Exit” button to exit current interface.
2.4.4.2 Motion
Pic 2-15 Motion
The setup steps of motion are familiar with schedule
Note: the default schedule of motion detection is full-selected, that is, the color of
schedule setting interface is blue.
2.4.4.3 Sensor
Pic 2-16 Sensor
The setup steps of alarm are familiar with schedule
Note: the default schedule of sensor is full-selected, that is the color of schedule
setting interface is blue.
2.4.5 Alarm configuration
Alarm configuration includes five sub menus: sensor, motion,video loss and alarm out.
16
2.4.5.2 Motion
Motion includes one sub menus: motion
1> Motion
Pic 2-21 Motion
Click start motion alarm and set alarm hold time，It refers to after close motion alarm it
delay to the preset setting time. Click alarm "Settings" button, show below window：
Pic 2-22 Alarm handling
Alarm configuration, trigger video alarm handling, linkage alarm handling
and sensor alarm handling trigger settings is same.
Click on "Area Settings" button at Motion detection interface,trun to the
following window;
Pic 2-23 Motion detection - Regional Settings
At area Setting interface, users can drag the slider to adjust the sensitivity value (1-5),
the default value is 4, 1-5 sensitivity progressive increase. Sensitivity influenced by the color
of time (day or night), the users should adjust according to actual situation.click icon，
17
set All locales for the detection region；click icon，will clear setting detection region；
click icon，save setting；click button,exit from current interface.
User can setup all channels with same parameters, please tick off “All”, and then to
do relevant setup.
Click “Default” button to resort default setting; Click “Apply” button to save the setting;
click “Exit” button to exit current interface.
2.4.5.3 Video loss
Pic 2-24 Video loss
Click“Alarm handling”button，turn to window as below：
Pic 2-25 Video loss - alarm handling
The setup steps of video loss trigger are familiar with alarm handling.
User can also setup all channels with same parameters，。click “Apply” button to save
the setting; click “Exit” button to exit current interface.
Click “Default” button to resort default setting；
Disconnected from the network: when the network connection is disconnected, the system
will automatically sent E-mail to the user specified mailbox about the network
disconnected.
2> Buzzer
At buzzer interface，tick off Buzzer, set buzzer alarm hold time
2.4.6 Network configuration
Network configuration includes four submenus: network, sub stream, Email and other
settings.
18
2.4.6.1 Network
Pic 2-27 Network configuration
HTTP port：the default value is 80. If the value changed, user needs to add the port
number when typing IP address in IE address blank. IE set HTTP port to 82, IP address:
http://192.168.0.25 , user needs to input that address: http://192.168.0.25:82 into IE
browser.
Server port: data and image communication port NO. After selecting the "Obtain an
IP address automatically", the device will distribute IP address, subnet mask, and gateway
IP and DNS server.
Enable PPPoE to directly connect the DVR to internet via ADSL and then input the
user name and password; click TEST button to test the effectiveness of the relevant
information.
Click “Default” button to resort default setting；click “Apply” button to save the setting;
Click “Exit” button to exit current interface.
2.4.6.2 Network Sub stream
Pic 2-28 Network Sub strea
select fps, resolution, quality.，user can also setup all channels with same parameters.
click “Apply” button to save the setting; click “Exit” button to exit current interface.
network configuration-network.
Parameter Meaning
FPS
Range from: 1-30（NTSC）1-25(PAL)
Resolution
Support CIF、QCIF
Quality
The higher the value is, the clearer the record image. Six
19
options: lowest, lower, low, medium, higher and highest.
2.4.6.3 Email
Pic 2-29 Email
SMTP Server/Port: the name and port number of SMTP server.
Send address/password: sender’s email address/password.
Receive address: receiver’s email address. Here user can add at least three mail
addresses.
Click Test button to test the validity of the mailbox.
Click “Default” button to resort default setting；click “Apply” button to save the setting;
click “Exit” button to exit current interface.
2.4.6.4 Other settings
Pic 2-30 Other settings
Enable DDNS server: user needs to input user name， password and host domain
name of the registered website, click TEST to test the effectiveness of the relevant
information. click “Default” button to resort default setting; click “Apply” button to save the
setting; click “Exit” button to exit current interface.
Note: the user select a domain name is bound by the Domain Name Service for DVR,
you must first landing the website of the ISP registered user name and password, and
then apply for a domain name for the server online. After the application is successful, the
user could enter the domain name to access the server in IE side.
20
2.4.7 User management
Enter User management , as below pic：
Pic 2-31 User management
Clicking Add button, a dialog box will pop-up as below：
Pic 2-32 General
1
General: Input user name, password; select user type, input the MAC address of
the PC; click OK button, this user will be added into the user list box; click Exit button to exit
the current interface.
2
Authority:
Pic 2-33 Authority:
21
In the authority interface, assign the definite operation right for that user.
In the user management interface, click Setup button to modify user name, user type
and binding PC MAC address.
Select the user that user wants to delete in the user list box and then click “Delete”
button to delete this user. click Change password button to modify the password and then
click “Exit” button to exit the current interface.
2.4.8 Advance configuration
Advanced settings include three sub-menu: factory settings, andimport / export and
exit.
1. Factory settings: all settings back to factory settings.
2. Import / Export: Users can export data files to be backed up onremovable storage
devices, you can also import the specified data file from a removable storage device to a
DVR.
3. Exit: exit current interface.
Pic 2-41 Advance configuration
Returned to the main menu, enter the data retrieval interface.
2.5 Data retrieval
Search configuration includes two submenus: Time Search, Event Search,
2.5.1 Time search
Step1：enter into Search configurationTime Search; refer to below pic：
22
Pic 2-42 Time search
Step 2：Select the channel, the calendar date , the start time and end time
Step 3：click“Play” button, Playback will start from the set time bucket; click the
corresponding button on the screen to start concrete operations.
Pic 2-43 Playback buttons
23
2.5.2 Event search
Step1:：enter into Search configurationevent search; refer to below pic.
Pic 2-44 Event search
Step2：After clicking Search button, the searched event information will displayed in
the event list box, double check a certain record file to playback.
Step3：User can select date, channel. Tick off Motion, Sensor or All accordingly to
search.
24
2.6 Backup
This unit supports backup by USB device，User also can make backup by IE browser
via internet.
Step1: enter into backup configuration interface, as below pic：
Pic 2-45 Data backup
Step2: set the start & end time, select channels and click Search button to display the
searched data in the data backup list box.
Step3: checked a data file or tick off “All” to select all data files, click “Backup” button,
Step4: in the backup information interface, user can check the relevant information of
backup files, storage type, save file type, etc. click “Start” button to starting backup.
2.7 Check information
Through this option, the user can check system information, system journal, network
information
System Information:
Enter menu
view information
system information， in the interface user can view
the equipment and version information and relevant information
Log information:
Enter menu
View system information
Log information，in the interface users can
set the start & end time of log you want to view, select the type of log you want to
view and click the search button, searched the log information will be displayed in
the log list box.
Note: Users can export data files to be backed up on removable storage devices.
Network information:
Enter menu view information Network configuration，in the interface，Users
can view the relevant parameters of the network information .
25
2.8 Disk management
Enter menu
Disk management，In the interface, the user can
view disk storage state, also can choose to formatting the hard disk
Please format the hard disk before record ,Specific operation as below：.
Step1: enter into disk management interface， The system will pop up the Disk
Management window.
Step2: select a hard disk and click Format button to star format.；set the property of the
disk then click “Apply” button to save the setting.
Note: all recorded files in the hard disk will be lost after formatted.
26
2.9 Upgrade
Once have the new version, the user can choose to upgrade the panel and the
mianboard, can get upgraded software from the buyers, to upgrade the system.
Upgrade step：user needs to copy the upgrade software which get from vendor into
the USB storage device and then connect to the USB port. Enter Menu Upgrade，refresh list，
the upgrade software name is displayed in the upgrade list box, select that software and click
Upgrade button to start upgrading. System will automatically restart on the upgrade process，
Please wait for a while when the system is rebooted. Please don’t cut off power during
upgrading. This system supports the upgrade of the USB device but it must be
compatible with the USB device, need to reboot the system after the upgrade completed to
take effect.
Note: If the upgraded software does not appeared in USB, usually the USB
devices are not compatible.
2.10 Logoff
Enter Menu
Logoff，Click Log off icon, The system will exit the current user login. If
user wants to log in again, click mian menu icon to enter into user name and password to
re-login.
2.11 System shut down
Click“system shut down”icon, shut down system.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AceSee AS-0410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AceSee AS-0410 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info