543896
41
Zoom out
Zoom in
Previous page
1/58
Next page
Acer Projector
P1173/X1171/X1173/X1173A/
X1173N/X1173H/X1273/X1273N/
X1273H/X1373W/X1373WH
Series User's Guide
Copyright © 2013. Acer Incorporated.
All Rights Reserved.
Acer Projector User's Guide
Original Issue: 11/2013
Acer Projector
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
"HDMI
TM
, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC."
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
iii
Information for Your Safety and
Comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices or lamp.
Using electrical power
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (14.76 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
Do not look into the projector's lens when the lamp is on. The bright light
may hurt your eyes.
Turn on the projector first and then signal sources.
Do not place the product in the following environments:
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector are necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shorten the life span and darken the image.
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, please ensure the projector completes
its cooling cycle before disconnecting power.
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to stop
before turning main power off.
Do not touch the air outlet grille and bottom plate which become hot.
Clean the air filter frequently. The temperature inside may rise and cause
damage when the filter/ventilation slots are clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when warning messages display.
When changing the lamp, please allow the projector to cool down, and
follow all changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen Display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/
Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
"Lamp(s) contain Mercury,
Dispose Properly."
viii
First Thing First
Usage Notes
Do:
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the display
housing.
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
Block the slots and openings on the projector provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place in direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
Please do not open or disassemble the product as this may cause electric shock.
When changing the lamp, please allow the projector to cool down, and follow all
changing instructions.
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
Reset the "Lamp Hour Reset" function from the Onscreen Display "Management"
menu after replacing the lamp module.
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
Turn on the projector first and then the signal sources.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Information for Your Safety and Comfort iii
First Thing First viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 2
Projector Overview 3
Projector Outlook 3
Control Panel 4
Remote Control Layout 5
MHL Feature Introduction 7
Getting Started 8
Connecting the Projector 8
Turning the Projector On/Off 9
Turning On the Projector 9
Turning Off the Projector 10
Adjusting the Projected Image 11
Adjusting the Height of the Projected Image 11
How to Optimize Image Size and Distance 12
How to Get a Preferred Image Size by
Adjusting Distance and Zoom 14
User Controls 16
Installation Menu 16
Onscreen Display (OSD) Menus 17
Color 18
Image 20
Setting 22
Management 25
Audio 25
3D 26
Language 27
Appendices 28
Contents
Troubleshooting 28
LED & Alarm Definition Listing 32
Replacing the Lamp 33
Ceiling Mount Installation 34
Specifications 37
Compatibility Modes 40
Regulations and safety notices 44
1
English
Introduction
Product Features
This product is a single-chip DLP
®
projector, including the following
outstanding features:
DLP
®
technology
P1173/X1171/X1173/X1173A/X1173N/X1173H: Native 800 x 600 SVGA
resolution, Auto/4:3/16:9 aspect ratio supported
X1273/X1273N/X1273H: Native 1024 x 768 XGA resolution, Auto/4:3/16:9
aspect ratio supported
X1373W/X1373WH: Native 1280 x 800 WXGA resolution,Auto/Full/4:3 /
16:9/L.Box aspect ratio supported
Enables projecting 3D content via DLP Link Technology: Blu-Ray 3D
supported (P1173/X1173H/X1273H/X1373WH)
One-touch "3D" button on remote control allows quick and easy access to
the 3D functions
Acer ColorBoost technology delivers vivid, life-like images
High brightness and contrast ratio
Versatile display modes enable optimum performance in any situation
NTSC/PAL/SECAM compatible and HDTV (720p, 1080i, 1080p) supported
Lower power consumption and economy (ECO) mode extends lamp life
Dynamic Black / ExtremeEco functions help decrease lamp power
consumption and further extend lamp life.
-
Dynamic Black: If turned on, the projector dynamically adjusts the power
consumption of the lamp according to the brightness of the image being
projected. When projecting darker images the power consumption will
be reduced and the contrast of the image will also be enhanced.
-
ExtremeEco: The projector will decrease the power consumption of the
lamp by up to 70% when no input signal can be detected for 5 minutes.
Acer EcoProjection Technology delivers Intelligent power management
approach and physical efficiency improvement
Advanced keystone correction delivers optimum presentations
Multi-language Onscreen Display (OSD) menus
Manual focus/zoom projection lens
2X digital zoom and pan move function
Microsoft
®
Windows
®
2000, XP, 7, Vista
®
, Macintosh OS compliant
2
English
Package Overview
This projector comes with all the items shown below. Check to make sure you
have them all. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
Security card User’s guide (CD-ROM) Remote control
Quick start guide Battery x 2 Carrying case
(Optional)
Dust filter
(Optional)
3
English
Projector Overview
Projector Outlook
Front/upper side
Rear side
# Description # Description
1 Control panel 5 Zoom ring
2 Projection lens 6 Focus ring
3 Tilt adjusting wheel 7 Remote control receiver
4 Power key and Power indicator LED
# Description # Description
1 RS232 connector 7 Audio input connector
2 Mini USB connector Audio output connector
3 HDMI (MHL) connector 8 Power socket
4 Analog RGB signal/HDTV/component
video input connector
9 Tilt adjusting wheel
5 Monitor loop-through output connector 10 Kensington™ lock port
6 S-Video input connector
Composite video input connector
1
5
6
4
3
2
7
-1
-2
-1
-2
4
English
Control Panel
# Function Description
1 LAMP Lamp Indicator LED.
2POWER indicator
LED
Refer to the "Turning the Projector On/Off" section.
3 Keystone Adjusts image distortion caused by tilting projection
(±40 degrees).
4 RESYNC Automatically synchronizes the projector to the input
source.
5 MENU Launches the Onscreen Display (OSD) menu, returns to
the previous step for the OSD menu operation or exits
the OSD menu.
6 Power key Refer to the "Turning the Projector On/Off" section.
7 TEMP Temp Indicator LED.
8 SOURCE Chooses RGB, component video, S-Video, composite
video, HDMI or HDTV source.
9 Four directional
selection keys
Selects items or makes adjustments to your selection
10 MODE Chooses a display mode.
1
7
8
3
3
5
6
10
9
4
2
5
English
Remote Control Layout
# Function Description
1 POWER Refer to the "Turning the Projector On/Off" section.
2 MEDIA SETUP Opens MEDIA SETUP page.
3 ZOOM Zooms the projector display in or out.
4 MODE Chooses a display mode.
5
Keystone
Adjusts image distortion caused by tilting projection
(±40 degrees).
Four
directional
selection
keys
Selects items or makes adjustments to your selection.
6 Keypad 0~9 Press "0~9" to input a password in the "Setting" >
"Security" OSD.
7 VGA To change source to VGA. This connection supports
analog RGB, YPbPr (480p/576p/720p/1080i/1080p), and
YCbCr (480i/576i).
8 COMPONENT To change source to Component video. This connector
supports YPbPr.
9 S-VIDEO To change source to S-Video.
10 HDMI™/DVI To change source to HDMI™ (or DVI). (for the model
with HDMI™ or DVI connector)
11 Infrared
transmitter
Sends signals to the projector.
12 FREEZE To pause the screen image.
Model No:E-26171
MC.JG811.009
(X1171/X1173N/
X1173H/X1273/
X1273N/X1273H)
(P1173/X1173/
X1173A/X1373W/
X1373WH)
6
English
13 SOURCE Chooses RGB, component video, S-Video, composite
video, HDMI or HDTV source.
14 HIDE Press "HIDE" to hide screen image; press again to
display the image.
15 MENU Launches the Onscreen Display (OSD) menu, returns to
the previous step for the OSD menu operation or exits
the OSD menu.
16 PgUp/PgDn For computer mode only. Use this button to select the
next or previous page. This function is only available
when connected to a computer via a USB cable.
17 VIDEO To change source to composite video.
18 RATIO Chooses an aspect ratio.
19 WIRELESS;
LAN/WiFi
(No function)
20
Rewind
Play/Pause
Stop
Fast-forward
(No function)
21 SD/USB A (No function)
22 USB B (No function)
23 3D Press to open the 3D menu for adjusting 3D settings.
# Function Description
7
English
MHL Feature Introduction
When your smartphone is connected to the projector, you can use some buttons
on the remote control to control your smartphone. Press "MODE" for one
second to enter or leave the MHL control mode. After entering the MHL control
mode, press "SOURCE" to switch between the navigation mode (default),
media mode and numeric mode.
# Function
Description
Navigation
mode
Media mode Numeric mode
4 MODE Long press for one second to enter or leave the
MHL control mode.
13 SOURCE After entering the MHL control mode, press to
switch between the navigation mode (default),
media mode and numeric mode.
5Four
directional
select keys
Up Up (No function) (No function)
down down (No function) (No function)
Left Left Decreases the
volume.
(No function)
Right Right Increases the
volume.
(No function)
6 Keypad 0~9 (No function) (No function) Enters 0~9.
15 MENU Goes to the
root menu.
(No function) (No function)
20
Rewind
(No function)
Rewinds/Plays/
Pauses/Stops/
Fast-forwards
the playing
media files.
Enters 1.
Play/Pause
Selects or
enters items.
Enters 2.
Stop
Exits current
page.
Enters 3.
Fast-forward
(No function) (No function)
8
English
Getting Started
Connecting the Projector
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Some smartphones require a converter (supplied by the
smartphone maker) to enable the MHL function.
# Description # Description
1 Power cord 6 S-Video cable
2 VGA cable 7 RS232 cable
3 VGA to component video/HDTV adapter 8 USB cable
4 Composite video cable 9 3 RCA component cable
5 Audio cable 10 HDMI (MHL) cable
-1
-2
RB G
RB G
HDTV adapter
D-Sub
9
3
DVD player,
Set-top box,
HDTV receiver
VGA
RS232
Video/S-Video
Output
Display
Speakers
9
English
Turning the Projector On/Off
Turning On the Projector
1 Ensure that the power cord and signal cable are securely connected.
The Power LED will light red.
2 Turn on the projector by pressing (POWER) on the control panel or
remote control, and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player, etc.). The
projector will detect your source automatically (when the Source Lock
function is disabled).
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
If you connect to multiple sources at the same time, use "SOURCE" on
the control panel or remote control, or the direct source key on the
remote control to switch between inputs.
1 & 2
10
English
Turning Off the Projector
1 To turn the projector off, press the power button. This message
appears:
"Please press power button again to complete the shutdown process"
Press the power button again.
2 The LED Power indicator will turn solid red to indicate standby mode.
3 It is now safe to unplug the power cord.
When Instant Resume is selected:
1 The LED Power indicator will turn RED and blink rapidly after the
projector is turned off, and the fan(s) will continue to operate for
about 2 minutes to ensure that the system cools properly.
2 As long as the power cord remains plugged in, you can press the
power button to turn the projector immediately back on anytime
during the 2-minute shutdown process.
3 Once the system has finished cooling, the LED Power indicator will
stop blinking and turn solid red to indicate standby mode.
4 It is now safe to unplug the power cord.
Warning indicators:
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp will automatically turn off, the projector will automatically
shut down, and the LED Temp indicator will turn solid red. Contact
your local dealer or service center.
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED Temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and
the
LED Temp indicator turns solid red, contact your local
reseller or service center
.
11
English
Adjusting the Projected Image
Adjusting the Height of the Projected Image
The projector is equipped with two elevator feet for adjusting the image
height.
To raise the image:
1 Use the front Tilt adjusting wheel to raise the image to the desired
height and angle.
2 Use the rear Tilt adjusting wheel to fine-tune the display angle.
To lower the image:
1 Use the front Tilt adjusting wheel to lower the image to the desired
height angle.
2 Use the rear Tilt adjusting wheel to fine-tune the display angle.
1
2
Tilt adjusting wheel
Tilt adjusting wheel
12
English
How to Optimize Image Size and Distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
SVGA/XGA
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 72" and 79".
Note: Remind as below figure, the space of 133 cm height is
required when the projector is located at 3 m distance.
Desired
Distance
(m)
< A >
Minimum Screen Size (Min zoom) Maximum Screen Size (Max zoom)
Diagonal
(inch)
< B >
W (cm) x H (cm)
From base to
top of image
(cm)
< C >
Diagonal
(inch)
< B >
W (cm) x H (cm)
From base to
top of image
(cm)
< C >
1 24 49 x 37 40 26 54 x 40 44
1.5 36 74 x 55 61 40 81 x 60 67
2 48 98 x 74 81 53 108 x 81 89
2.5 60 123 x 92 101 66 134 x 101 111
3 72 147 x 110 121 79 161 x 121 133
3.5 84 172 x 129 142 93 188 x 141 155
4 96 196 x 147 162 106 215 x 161 177
4.5 108 221 x 165 182 119 242 x 181 200
5 120 245 x 184 202 132 269 x 202 222
6 144 294 x 221 243 159 323 x 242 266
7 168 343 x 257 283 185 376 x 282 310
8 192 392 x 294 324 212 430 x 323 355
9 216 441 x 331 364 238 484 x 363 399
10 241 490 x 368 404 265 538 x 403 444
11 265 539 x 404 445 291 591 x 444 488
12 289 588 x 441 485 318 645 x 484 532
Zoom Ratio: 1.1 x
3 m
Desired distance
Height:
121 cm
Height:
133 cm
From
base to
top of
image
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
72"
79"
13
English
WXGA
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 84" and 93".
Note: Remind as below figure, the space of 125 cm height is
required when the projector is located at 3 m distance.
Desired
Distance
(m)
< A >
Minimum Screen Size (Min zoom) Maximum Screen Size (Max zoom)
Diagonal
(inch)
< B >
W (cm) x H (cm)
From base to
top of image
(cm)
< C >
Diagonal
(inch)
< B >
W (cm) x H (cm)
From base to
top of image
(cm)
< C >
1 28 61 x 38 38 31 67 x 42 42
1.5 42 91 x 57 57 46 100 x 63 63
2 56 121 x 76 76 62 133 x 83 83
2.5 70 152 x 95 95 77 167 x 104 104
3 84 182 x 114 114 93 200 x 125 125
3.5 98 212 x 133 133 108 233 x 146 146
4 113 242 x 152 152 124 267 x 167 167
4.5 127 273 x 170 170 139 300 x 188 188
5 141 303 x 189 189 155 333 x 208 208
6 169 364 x 227 227 186 400 x 250 250
7 197 424 x 265 265 217 467 x 292 292
8 225 485 x 303 303 248 533 x 333 333
9 253 545 x 341 341 279 600 x 375 375
10 281 606 x 379 379 310 667 x 417 417
11 310 667 x 417 417 340 733 x 458 458
12 338 727 x 455 455 371 800 x 500 500
Zoom Ratio: 1.1 x
3 m
Desired distance
Height:
114 cm
Height:
125 cm
From
base to
top of
image
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
84"
93"
14
English
How to Get a Preferred Image Size by Adjusting
Distance and Zoom
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
SVGA/XGA
To obtain an image size of 70", set the projector at a distance between 2.6 m
and 2.9 m from the screen and adjust the zoom level accordingly.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
< A >
W (cm) x H (cm)
Max zoom
< B >
Min zoom
< C >
From base to top of
image < D >
30 61 x 46 1.2 50
40 81 x 61 1.5 1.7 67
50 102 x 76 1.9 2.1 84
60 122 x 91 2.3 2.5 101
70 142 x 107 2.6 2.9 117
80 163 x 122 3.0 3.3 134
90 183 x 137 3.4 3.7 151
100 203 x 152 3.8 4.2 168
120 244 x 183 4.5 5.0 201
150 305 x 229 5.7 6.2 251
180 366 x 274 6.8 7.5 302
200 406 x 305 7.6 8.3 335
250 508 x 381 9.4 10.4 419
300 610 x 457 11.3 503
Zoom Ratio: 1.1 x
Desired distance
Height:
117 cm
From base
to top of
image
70"
Desired
image size
2.6 m
2.9 m
15
English
WXGA
To obtain an image size of 70" set the projector at a distance between 2.3 m
and 2.5 m from the screen and adjust the zoom level accordingly.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
< A >
W (cm) x H (cm)
Max zoom
< B >
Min zoom
< C >
From base to top of
image < D >
30 65 x 40 1.1 40
40 86 x 54 1.3 1.4 54
50 108 x 67 1.6 1.8 67
60 129 x 81 1.9 2.1 81
70 151 x 94 2.3 2.5 94
80 172 x 108 2.6 2.8 108
90 194 x 121 2.9 3.2 121
100 215 x 135 3.2 3.6 135
120 258 x 162 3.9 4.3 162
150 323 x 202 4.8 5.3 202
180 388 x 242 5.8 6.4 242
200 431 x 269 6.5 7.1 269
250 538 x 337 8.1 8.9 337
300 646 x 404 9.7 404
Zoom Ratio: 1.1 x
Desired distance
Height:
94 cm
From base
to top of
image
70"
Desired
image size
2.3 m
2.5 m
16
English
User Controls
Installation Menu
The Installation menu provides an Onscreen Display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No
signal" is displayed on the screen.
1 Turn on the projector by pressing (POWER) on the control panel or
remote control.
2 Press "MENU" on the control panel or remote control to launch the
OSD for projector installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration
and alignment settings, such as screen size and distance, focus and
more.
Note: The OSD screenshot is for reference only and may differ from the
actual design.
4 The Installation menu includes several options.
Use the up and down arrow keys to select an option, the left and right arrow keys to
adjust selected option settings, and the right arrow key to enter a submenu for
feature setting. The new settings will be saved automatically upon exiting the menu.
5 Press "MENU" anytime to exit the menu and return to the Acer
welcome screen.
17
English
Onscreen Display (OSD) Menus
The projector has multilingual Onscreen Display (OSD) menus that allow
you to make image adjustments and change a variety of settings.
Using the OSD menus
To open the OSD menu, press "MENU" on the control panel or remote
control.
When the OSD is displayed, use to select an item in the main menu.
After selecting the desired main menu item, press to enter a submenu
for feature setting.
Use to select the desired item and adjust the settings by using
.
Select the next item to be adjusted in the submenu and adjust as described
above.
Press "MENU" on the control panel or remote control, the screen will
return to the main menu.
To exit the OSD menu, press "MENU" on the control panel or remote
control again. It will close and the projector will automatically save the
new settings.
Note: Some of the following OSD settings may not be available. Please refer
to the actual OSD of your projector.
Main menu
Submenu
Setting
18
English
Color
Display Mode
There are many factory presets optimized for various types
of images.
Bright: For brightness optimization.
Presentation: For meeting presentation with higher
brightness.
Standard: For common environment.
Movie: For brighter and general movie/video/photo
playing.
Dark Cinema: For dark movie content.
Video: For playing video in a bright environment.
Picture: For graphic picture.
Game: For game content.
Education: For education environment.
Sport: For sport picture.
User: Memorize user’s settings.
Wall Color
Use this function to choose a proper color according to the
wall. There are several choices, including White, Light
Yellow, Light Blue, Pink and Dark Green. It will compensate
for the color deviation due to the wall color to show the
correct image tone.
Brightness
Adjusts the brightness of the image.
Press to darken the image.
Press to lighten the image.
Contrast
Controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
Press to decrease the contrast.
Press to increase the contrast.
Saturation
Adjusts a video image from black and white to fully
saturated colors.
Press to decrease the amount of color in the
image.
Press to increase the amount of color in the
image.
19
English
Note: "Saturation" and "Tint" functions are not supported under computer
mode.
Tint
Adjusts the color balance of red and green.
Press to increase the amount of green in the
image.
Press to increase the amount of red in the image.
Color
Temperature
Adjusts the color temperature. At higher color
temperatures, the screen looks colder; at lower color
temperatures, the screen looks warmer.
Dynamic Black
If turned on, the projector dynamically adjusts the power
consumption of the lamp according to the brightness of
the image being projected. When projecting darker images
the power consumption will be reduced and the contrast of
the image will also be enhanced.
Gamma
Effects the representation of dark scenery. With greater
gamma value, dark scenery will look brighter.
20
English
Image
Projection
Front-Desktop: The factory default setting.
Front-Ceiling: When you select this function, the
projector inverts the image for ceiling-mounted
projection.
Rear-Desktop: When you select this function, the
projector reverses the image so that you can project
behind a translucent screen.
Rear-Ceiling: When you select this function, the
projector reverses and inverts the image at same time.
You can project from behind a translucent screen with
ceiling mounted projection.
Projection
Mode
Front: The factory default setting.
Rear: Reverses the image so you can project from
behind a translucent screen.
Projection
Location
Auto: Automatically adjusts projection location of
image.
Desktop
Ceiling: Turns the image upside down for ceiling-
mounted projection.
Aspect Ratio
Use this function to choose your desired aspect ratio.
Auto: Keeps the image with original width-height ratio
and maximizes the image to fit native horizontal or
vertical pixels.
Full (for WXGA models): The image will be displayed
making full use of the horizontal and vertical pixels.
4:3: The image will be scaled to fit the screen and
displayed using a 4:3 ratio.
16:9: The image will be scaled to fit the screen and
displayed using a 16:9 ratio.
L.Box (for WXGA models): Keeps the original signal
aspect ratio and zooms in by 1.333 times.
Auto Keystone
Automatically adjusts image distortion caused by tilting
projection (±40 degrees).
21
English
Keystone Manually adjusts image distortion caused by tilting
projection (±40 degrees).
This function is unavailable when Auto Keystone is set
to "On".
Manual
Keystone
Sharpness
Adjusts the sharpness of the image.
Press to decrease the sharpness.
Press to increase the sharpness.
H. Position
(Horizontal
Position)
Press to move the image left.
Press to move the image right.
V. Position
(Vertical
Position)
Press to move the image down.
Press to move the image up.
Frequency
Changes the projector’s refresh rate to match the frequency
of your computer’s graphics card. If you experience a vertical
flickering bar in the projected image, use this function to
correct it.
Tracking
Synchronizes the signal timing of the display with the
graphics card. If you experience an unstable or flickering
image, use this function to correct it.
HDMI Color
Range
Adjusts the color range of the HDMI image data to prevent
color display error.
Auto: Automatically adjusts the color range by
information from the player.
Limited Range: Processes the input image as limited
color range data.
Full Range: Processes the input image as full color range
data.
HDMI Scan Info
Adjusts the overscan ratio of the HDMI image on screen.
Auto: Automatically adjusts the overscan ratio by
information from the player.
Underscan: Always no overscan on the HDMI image.
Overscan: Always keep overscan on the HDMI image.
22
English
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under video mode.
Note: "Sharpness" function is not supported under computer mode.
Note: "HDMI Color Range" and "HDMI Scan Info" are only available when
the input signal is HDMI.
Setting
Startup Screen
Use this function to select your desired startup screen. If you
change the setting, it will take effect when you exit the OSD
menu.
Acer: The default startup screen of your Acer projector.
User: Use the memorized picture from the "Screen
Capture" function.
Screen Capture
Use this function to customize the startup screen. To capture
the image that you want to use as the startup screen, follow
the instructions below.
Notice
Before proceeding with the following steps, make sure that
the "Keystone" is set to the default value "0", and the
"Aspect Ratio" is set to "4:3". For details, refer to the "Image"
section.
Change the "Startup Screen" from the default setting
"Acer" to "User".
Select "Screen Capture" to customize the startup screen.
A dialog box appears to confirm the action. Choose
"Yes" to use the current image as your customized
startup screen. Choose "No" to cancel the screen capture
and exist the Onscreen Display (OSD).
A message appears stating that the screen capture is in
progress.
When the screen capture is finished, the message
disappears and the original display is shown.
Source Lock
Selecting "On" enables the function and when switching
input signals, you need to press "SOURCE" on the control
panel or remote control, or the direct source key on the
remote control. When this function is disabled, the projector
will detect your source automatically.
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2,
CC3, CC4 (CC1 displays captions in the primary language in
your area). Select "Off" to turn off the captioning feature.
This function is only available when a composite video or S-
Video input signal is selected and its system format is NTSC.
23
English
VGA OUT
(Standby)
Selecting "On" enables the function. The projector can output
a VGA signal when it is in standby mode and the VGA IN (or
VGA IN 1) and VGA OUT sockets are correctly connected to the
devices.
Enabling this function slightly increases the standby
power consumption.
Reset
Press after choosing "Yes" to return the display
parameters on all menus to the factory default settings.
Security
Security
This projector provides a useful security function for the
administrator to manage the projector.
Press to change the "Security" setting. If the security
function is enabled, your must enter "Administrator
Password" first before changing the security setting.
The factory default of "Administrator Password" is
"1234".
Select "On" to enable the security function. You have to
enter password depending on the "Security Mode".
Please refer to "User Password" section for details.
If "Off" is selected, you can switch on the projector
without password.
Timeout (Min.)
Once "Security" is set to "On", you can set timeout function.
Press to select timeout duration.
The range is from 10 to 990 minutes.
When time is up, the projector will request you to enter
the password again.
The factory default setting of "Timeout (Min.)" is "Off".
Once the security function is enabled, the projector will
request you to enter password when switching on the
projector. Both "User Password" and "Administrator
Password" can be accepted for this dialogue.
24
English
User Password
Press to set up or change "User Password".
Use the numerical keys on the remote control to set the
password and press "MENU" to confirm.
To delete the digits, Press .
Enter the password again when you see "Confirm
Password" displayed.
The password should be 4~8 digits in length.
If you select "Request password only after plugging
power cord", you are requested to input the password
every time the power cord is plugged.
If you select "Always request password while projector
turns on", you are requested to input the password every
time the projector is turned on.
Administrator Password
You can enter "Administrator Password" when the "Enter
Administrator Password" or "Enter Password" dialogue box
displays.
Press to change "Administrator Password".
The factory default of "Administrator Password" is
"1234".
If you forget your administrator password, do the following
to retrieve the administrator password:
Enter the unique 6-digit "Universal Password" which is
printed on the Security Card that came with your
projector. This unique password will be accepted by the
projector no matter what the administrator password is.
If the Security Card is lost, please contact your local Acer
service center.
Lock User Startup Screen
This function is set to "OFF" by default. If set to "ON", the
startup screen is locked and cannot be changed by the
"Startup Screen" and "Screen Capture" functions.
25
English
Management
Audio
ECO Mode
Choose "On" to dim the projector lamp, which will also
lower the power consumption, reduce noise, and extend
the lamp life. Choose "Off" to return to the normal mode.
High Altitude
Choose "On" to turn on the High Altitude mode. When
this function is turned on, the projector fans operate at full
speed continuously to cool down the projector’s
temperature.
Turn Off Mode
Instant Off: Enables you to turn off the projector
immediately without fan cooling process by pressing
the power button twice.
Instant Resume: Enables you to restart the projector
immediately within 2 minutes after turning it off.
Auto Shutdown
(Minutes)
The projector will automatically shut down while there is
no signal input detected after the time you set.
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding
Choose this function to show or hide warning message
when the changing lamp message is displayed. The
message will show up 30 hours before end of life.
Lamp Hour Reset
Press after choosing "Yes" to reset the lamp hour
counter to 0 hours.
Volume
Press to decrease the volume.
Press to increase the volume.
Mute
Choose "On" to turn mute on.
Choose "Off" to turn mute off.
Power On/Off
Volume
Select this function to adjust the notification volume
when turning the projector on/off.
Alarm Volume
Select this function to adjust the volume of any
warning notifications.
26
English
3D
Note: Supported 3D signal timings:
It needs correct settings on graphics card 3D application program for correct
3D display.
The SW players, such as Stereoscopic Player and DDD TriDef Media Player
can support 3D format files. You can download these players on the web
page below.
3D
Selects "On" to enable the 3D function supported by DLP 3D
technology.
On: Select this item while using DLP 3D glasses, quad
buffer (NVIDIA/ATI...) graphics card and HQFS format file
or DVD with corresponding SW player.
Off: Turns off the 3D mode.
3D Format
If the 3D content is not displayed correctly, you can select a
3D format that suits the 3D content you are viewing and
obtain the best result.
3D Sync Invert
If you see a discrete or overlapping image while wearing DLP
3D glasses, you may need to execute "Invert" to get best
match of left/right image sequence to get the correct image
(for DLP 3D).
24P 3D Choose 96Hz or 144Hz for 24p 3D.
3D Warning
Message
Choose "On" to display the 3D warning message.
Signal source type Supported timing
Video/S-Video/Component
video
HQFS 3D (480i@60Hz), 576i@50Hz
VGA/HDMI (PC mode) 640 x 480@50/60/100/120Hz
800 x 600@50/60/100/120Hz
1024 x 768@50/60/100/120Hz
1280 x 800@50/60/100/120Hz
HDMI (Video mode) HQFS 3D (480i@60Hz) , 576i@50Hz,
Frame Packing (1080p@23.98/24Hz,
720p@50/60Hz)
Side-by-Side Horizontal (1080i@50/60Hz,
1080p@50/60Hz)
Top-and-Bottom (720p@50/60Hz,
1080p@23.97/24Hz, 1080p@50/60Hz)
27
English
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-
3-D-Experience-4.0.2.html
Note: "3D Sync Invert" and "3D Format" are only available when "3D" is
enabled.
Language
Language
Sets a language for the OSD menus. Use to
select your preferred language.
28
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears
onscreen
Make sure all the cables are correctly connected as
described in the "Getting Started" section.
Ensure none of the connector pins are bent or
broken.
Check if the projection lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
Make sure the projector is switched on.
2 Partial, scrolling
or incorrectly
displayed image
(For PC (Windows
95/98/2000/XP/
Win7/Vista))
Press "RESYNC" on the control panel or remote
control.
For an incorrectly displayed image:
Open "My Computer > Control Panel," and
then double-click the "Display" icon.
Select the "Settings" tab.
Verify that your display resolution setting is
lower than or equal to 1600 x 1200 or 1920 x
1080.
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
Verify that the resolution setting is lower than
or equal to 1600 x 1200 or 1920 x 1080.
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices > Standard monitor
types" under the SP box, and choose the
resolution mode you need under the "Models"
box.
Verify that the resolution setting of the
monitor display is lower than or equal to 1600
x 1200 or 1920 x 1080.
29
English
3 Partial, scrolling
or incorrectly
displayed image
(For notebooks)
Press "RESYNC" on the control panel or remote
control.
For an incorrectly displayed image:
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
4 The screen of the
notebook
computer is not
displaying your
presentation
If you are using a Microsoft
®
Windows
®
based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
If you are using an Apple
®
Mac
®
OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On."
5 Image is unstable
or flickering
Use "Tracking" to correct it. Refer to the "Image"
section for more information.
Change the display color setting on your computer.
6 Image has vertical
flickering bar
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7 Image is out of
focus
Adjust the focus ring on the projector lens.
Make sure the projection screen is within the
required distance:
4.9 to 19.7 feet (1.5 to 6 meters)
Refer to the "How to Get a Preferred Image Size by
Adjusting Distance and Zoom" section for more
information.
8 Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
If you play a 4:3 format DVD title, please change the
format to 4:3 with the projector OSD.
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
30
English
Problems with the Projector
9 Image is too small
or too large
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the
screen.
Press "MENU" on the control panel or remote
control. Go to "Image" > "Aspect Ratio" and try
different settings.
10 Image has slanted
sides
If possible, reposition the projector so that it is
centered on the screen and below the bottom of the
screen.
Press the Keystone correction keys on the control
panel or remote control until the image becomes
square.
Press "MENU" on the control panel or remote
control to open the OSD menu. Go to "Image" >
"Auto Keystone" or "Image" > "Keystone" to make
adjustments.
11 Image is reversed
Select "Image" > "Projection Mode", "Image" >
"Projection Location" on the OSD and adjust the
projection direction.
# Condition Solution
1 The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2 Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
31
English
OSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it is used. Please also check the dust filters if
they are installed. If the dust filter is clogged with dust, please
clean it.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
Fan Fail.
Lamp will automatically turn off soon.
Projector Overheated.
Lamp will automatically turn off soon.
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acer X1273H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acer X1273H in the language / languages: English as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Acer X1273H

Acer X1273H User Manual - German - 62 pages

Acer X1273H User Manual - Dutch - 62 pages

Acer X1273H User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info