Manual Acer X1161PN (page 56 of 56) (English)

535789

Zoom out

Zoom in

1/56

Acer Projector

X1161P/X1161PA/X1161PN/X112/

X1261P/X1261PN Series

User's Guide

Changes may be made periodically to the information in this publication without obligation

to notify any person of such revisions or changes. Such changes will be incorporated in new

editions of this manual or supplementary documents and publications. This company makes

no representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims the implied warranties of merchantability or fitness for a

particular purpose.

Record the model number, serial number, purchase date and place of purchase information in

the space provided below. The serial number and model number are recorded on the label

affixed to your projector. All correspondence concerning your unit should include the serial

number, model number and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in

any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,

without the prior written permission of Acer Incorporated.

Model number: __________________________________

Serial number: ___________________________________

Date of purchase: ________________________________

Place of purchase: ________________________________

Acer Projector X1161P/X1161PA/X1161PN/X112/X1261P/X1261PN Series User's Guide

Original Issue: 11/2012

Acer Projector X1161P/X1161PA/X1161PN/X112/X1261P/X1261PN Series

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product

names or trademarks are used herein for identification purposes only and belong to their respective

companies.

iii

Information for your safety and

comfort

Read these instructions carefully. Keep this document for future reference.

Follow all warnings and instructions marked on the product.

Turning the product off before cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Caution for plug as disconnecting device

Observe the following guidelines when connecting and disconnecting power to

the external power supply unit:

• Install the power supply unit before connecting the power cord to the AC

power outlet.

• Unplug the power cord before removing the power supply unit from the

projector.

• If the system has multiple sources of power, disconnect power from the

system by unplugging all power cords from the power supplies.

Caution for Accessibility

Be sure that the power outlet you plug the power cord into is easily accessible

and located as close to the equipment operator as possible. When you need to

disconnect power to the equipment, be sure to unplug the power cord from the

electrical outlet.

Warnings!

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. If the product

falls, it could be seriously damaged.

• Slots and openings are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating. These

openings must not be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug or other similar surface.

This product should never be placed near or over a radiator or heat register, or

in a built-in installation unless proper ventilation is provided.

• Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short-out parts that could

result in a fire or electric shock. Never spill liquid of any kind onto or into

the product.

• To avoid damage of internal components and to prevent battery leakage,

do not place the product on a vibrating surface.

• Never use it under sporting, exercising, or any vibrating environment

which will probably cause unexpected short current or damage rotor

devices, lamp.

Using electrical power

• This product should be operated from the type of power indicated on the

marking label. If you are not sure of the type of power available, consult

your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this

product where people will walk on the cord.

• If an extension cord is used with this product, make sure that the total

ampere rating of the equipment plugged into the extension cord does not

exceed the extension cord ampere rating. Also, make sure that the total

rating of all products plugged into the wall outlet does not exceed the fuse

rating.

• Do not overload a power outlet, strip or receptacle by plugging in too

many devices. The overall system load must not exceed 80% of the branch

circuit rating. If power strips are used, the load should not exceed 80% of

the power strip's input rating.

• This product's AC adapter is equipped with a three-wire grounded plug.

The plug only fits in a grounded power outlet. Make sure the power outlet

is properly grounded before inserting the AC adapter plug. Do not insert

the plug into a non-grounded power outlet. Contact your electrician for

details.

Warning! The grounding pin is a safety feature. Using a power outlet that is

not properly grounded may result in electric shock and/or injury.

Note: The grounding pin also provides good protection from unexpected

noise produced by other nearby electrical devices that may interfere with

the performance of this product.

• Use the product only with the supplied power supply cord set. If you need

to replace the power cord set, make sure that the new power cord meets

the following requirements: detachable type, UL listed/CSA certified, VDE

approved or its equivalent, 4.5 meters (15 feet) maximum length.

Product servicing

Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage points or other risks. Refer all servicing to

qualified service personnel.

Unplug this product from the wall outlet and refer servicing to qualified service

personnel when:

• the power cord or plug is damaged, cut or frayed

• liquid was spilled into the product

• the product was exposed to rain or water

• the product has been dropped or the case has been damaged

• the product exhibits a distinct change in performance, indicating a need

for service

• the product does not operate normally after following the operating

instructions

Note: Adjust only those controls that are covered by the operating

instructions, since improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to

restore the product to normal condition.

Warning! For safety reasons, do not use non-compliant parts when adding

or changing components. Consult your reseller for purchase options.

Your device and its enhancements may contain small parts. Keep them out of

the reach of small children.

Additional safety information

• Do not look into the projector's lens when the lamp is on. The bright may

hurt your eyes.

• Turn on the projector first and then signal sources

• Do not place the product in following environments:

• Space that is poorly ventilated or confined. At least 50cm clearance from walls

and free flow of air around the projector is necessary.

• Locations where temperatures may become excessively high, such as inside of a

car with all windows rolled up.

• Locations where excessive humidity, dust, or cigarette smoke may contaminate

optical components, shortening the life span and darkening the image.

• Locations near fire alarms.

• Locations with an ambient temperature above 40 ºC/104 ºF.

• Locations where the altitudes are higher than 10000 feet.

• Unplug immediately if there is something wrong with your projector. Do

not operate if smoke, strange noise or odor comes out of your projector. It

might cause fire or electric shock. In this case, unplug immediately and

contact your dealer.

• Do not keep using this product to break or drop it. In this case contact your

dealer for inspection.

• Do not face the projector lens to the sun. It can lead to fire.

• When switching the projector off, suggest to ensure the projector

completes its cooling cycle before disconnecting power.

• Do not frequently turn off the main power abruptly or unplug the

projector during operation. The best way is to wait for the fan to turn off

before turning main power off.

• Do not touch air outlet grille and bottom plate which becomes hot.

• Clean the air filter frequently if have. The temperature inside may rise and

cause damage when the filter/ventilation slots clogged with dirt or dust.

• Do not look into the air outlet grille when projector is operating. It may

hurt your eyes.

• Always open the lens shutter or remove the lens cap when the projector is

on.

• Do not block the projector lens with any object when the projector is

under operation as this could cause the object to become heated and

deformed or even cause a fire. To temporarily turn off the lamp, press HIDE

on the remote control.

• The lamp becomes extremely hot during operation. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for

replacement.

• Do not operate lamps beyond the rated lamp life. It could cause it to break

on rare occasions.

• Never replace the lamp assembly or any electronic components unless the

projector is unplugged.

• The product will detect the life of the lamp itself. Please be sure to change

the lamp when is showing warning message.

• When changing the lamp, please allow unit to cool down, and follow all

changing instructions.

• Reset the "Lamp Hour Reset" function from the Onscreen display

"Management" menu after replacing the lamp module.

• Do not attempt to disassemble this projector. There are dangerous high

voltages inside which may hurt you. The only user serviceable part is the

lamp which has its own removable cover. Refer servicing only to suitable

qualified professional service personnel.

• Do not stand the projector on end vertically. It may cause the projector to

fall over, causing injury or damage.

• This product is capable of displaying inverted images for ceiling mount

installation. Only use acer ceiling mount kit for mounting the projector

and ensure it is securely installed.

vii

Caution for Listening

To protect your hearing, follow these instructions.

• Increase the volume gradually until you can hear clearly and comfortably.

• Do not increase the volume level after your ears have adjusted.

• Do not listen to music at high volumes for extended periods.

• Do not increase the volume to block out noisy surroundings.

• Decrease the volume if you can't hear people speaking near you.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize

pollution and ensure utmost protection of the global environment, please

recycle. For more information on the Waste from Electrical and Electronics

Equipment (WEEE) regulations, visit http://www.acer-group.com/public/

Sustainability/sustainability01.htm

Mercury advisory

For projectors or electronic products containing an LCD/CRT monitor or display:

Lamp(s) inside this product contain mercury and must be recycled or disposed of

according to local, state or federal laws. For more information, contact the

Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal

information, check www.lamprecycle.org

“Lamp(s) contain Mercury,

Dispose Properly.”

viii

First things first

Usage Notes

Do:

• Turn off the product before cleaning.

• Use a soft cloth moistened with mild detergent to clean the display

housing.

• Disconnect the power plug from AC outlet if the product is not being used

for a long period of time.

Don't:

• Block the slots and openings on the unit provided for ventilation.

• Use abrasive cleaners, waxes or solvents to clean the unit.

• Use under the following conditions:

• In extremely hot, cold or humid environments.

• In areas susceptible to excessive dust and dirt.

• Near any appliance that generates a strong magnetic field.

• Place In direct sunlight.

Precautions

Follow all warnings, precautions and maintenance as recommended in this

user's guide to maximize the life of your unit.

Warning:

• Do not look into the projector's lens when the lamp is on. The bright light may hurt

your eyes.

• To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

• Please do not open or disassemble the product as this may cause electric shock.

• When changing the lamp, please allow unit to cool down, and follow all changing

instructions.

• This product will detect the life of the lamp itself. Please be sure to change the lamp

when it shows warning messages.

• Reset the "Lamp Hour Reset" function from the Onscreen display "Management"

menu after replacing the lamp module.

• When switching the projector off, please ensure the projector completes its cooling

cycle before disconnecting power.

• Turn on the projector first and then the signal sources.

• Do not use lens cap when projector is in operation.

• When the lamp reaches the end of its life, it will burn out and may make a loud

popping sound. If this happens, the projector will not turn back on until the lamp

module has been replaced. To replace the lamp, follow the procedures listed under

"Replacing the Lamp".

Information for your safety and comfort iii

First things first viii

Usage Notes viii

Precautions viii

Introduction 1

Product Features 1

Package Overview 2

Projector Overview 3

Projector Outlook 3

Remote Control and Control Panel Layout 5

Getting Started 7

Connecting the Projector 7

Turning the Projector On/Off 8

Turning on the Projector 8

Turning the projector off 9

Adjusting the Projected Image 10

Adjusting the Height of Projected Image 10

How to optimize image size and distance 11

How to get a preferred image size by adjusting

distance and zoom 13

User Controls 15

Installation menu 15

Acer Empowering Technology 16

Onscreen Display (OSD) Menus 17

Color 18

Image 20

Setting 22

Management 24

Audio 24

3D 25

Language 26

Appendices 27

Contents

Troubleshooting 27

LED & Alarm Definition Listing 32

Replacing and cleaning the dust filters 33

Replacing the Lamp 34

Ceiling Mount Installation 35

Specifications 38

Compatibility modes 40

Regulations and safety notices 42

English

Introduction

Product Features

This product is a single-chip DLP

projector. Outstanding features include:

• DLP

technology

• X1161P/X1161PA/X1161PN/X112 series: Native 800 x 600 SVGA resolution

X1261P/X1261PN series: Native 1024 x 768 XGA resolution

4:3 / 16:9 aspect ratio supported

• Acer ColorBoost technology delivers nature’s true colors for vivid, life-like

images

• High brightness and contrast ratio

• Versatile display modes (Bright, Presentation, Standard, Video, Game,

Education, User) enable optimum performance in any situation

• NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported

• Lower power consumption and economy (ECO) mode extends lamp life

• Acer EcoProjeciton Technology delivers Intelligent power management

approach and physical efficiency improvement

• Empowering Key reveals Acer Empowering Technology utilities (Acer

eView, eTimer, ePower, e3D Management) for easy adjustment of settings

• Advanced digital keystone correction optimizes presentations

• Smart detection delivers quick, intelligent source detection

• Multi-language onscreen display (OSD) menus

• Manual focus projection lens zooms up to 1.1x

• 2x digital zoom and pan function

• Microsoft

Windows

2000, XP, Vista

, Windows 7, Macintosh

compliant

English

Package Overview

This projector comes with all the items shown below. Check to make sure your

unit is complete. Contact your dealer immediately if any thing is missing.

Projector Power cord VGA cable

Battery Security card User’s guide

Remote control Quick start guide Carrying case

(Optional)

Dust filters

(Optional)

XXXXXX

English

Projector Overview

Projector Outlook

Front / upper side

Rear side

# Description # Description

1 Zoom lens 6 Power button

2 Tilt adjusting wheel 7 Remote control

3 Remote control receivers 8 Ventilation (inlet)

4 Focus ring 9 Ventilation (outlet)

5 Zoom lever

VGA IN S-VI DEO

VIDEO

X1161P/X1161PA/X112

VGA IN

X1161PN/X1261PN

VGA IN S-VID EO VIDEO RS232 VGA OUT AUDIO IN

X261P

35421

English

Note: Connector interface is subject to model's specifications.

# Description # Description

1 PC analog signal/HDTV/component

video input connector

6 Audio input connector

2 S-Video input connector 7 Power socket

3 Composite video input connector

Kensington

lock port

4 RS232 connector 9 USB ctrl connector

Monitor loop-through output

connector (VGA-Out)

English

Remote Control and Control Panel Layout

# Icon Function Description

1 Remote control

receiver

Receives signals from remote control.

2 POWER Refer to the "Turning the Projector On/Off" section.

3 MENU

• Press "MENU" to launch the Onscreen display (OSD)

menu, back to the previous step for the OSD menu

operation or exit the OSD menu.

• Confirm your selection of items.

4 VGA Press "VGA" to change source to the VGA connector. This

connector supports analog RGB, YPbPr (480p/576p/720p/

1080i), YCbCr (480i/576i) and RGBsync.

5 VIDEO Press "VIDEO" to change source to composite video. (for

X1161P/X1161PA/X112/X1261P series only)

6 S-VIDEO Press "S-VIDEO" to change source to S-Video. (for X1161P/

X1161PA/X112/X1261P series only)

7 ZOOM Zooms the projector display in or out.

8 SOURCE Changes the active source.

9 RESYNC Automatically synchronizes the projector to the input source.

10 ASPECT RATIO To choose the desired aspect ratio (Auto/4:3/16:9).

FREEZE To pause the screen image.

English

Note:

Remote Control Placement

Please refer to the illustration to attach the remote control to the projector.

12 HIDE Momentarily turns off the video. Press "HIDE" to hide the

image, press again to display the image.

13 Empowering

key

Unique Acer functions: eView, eTimer, ePower Management.

14 KEYSTONE Adjusts the image to compensate for distortion caused by

tilting the projector (± 40 degrees).

15 Four directional

select keys

Use up, down, left, right buttons to select items or make

adjustments to your selection.

16 KeyPad 0~9 Press "0~9" to input a password in the "Security".

# Icon Function Description

English

Getting Started

Connecting the Projector

Note: To ensure the projector works well with your computer,

please make sure the timing of the display mode is compatible

with the projector.

Note: Connector interface is subject to model's specifications.

Note: USB cable needs powered extender if the length is over 5 m.

# Description # Description

1 Power cord 5 Audio cable jack/jack

2 USB cable 6 S-Video cable

3 VGA cable 7 Composite video cable

4 RS232 cable 8 Audio cable jack/RCA

VGA IN S-VID EO VIDEO RS232 VGA OUT AUDIO IN

VGA

D-Sub

RS232

USB

S-Video output

Video output

English

Turning the Projector On/Off

Turning on the Projector

1 Ensure that the power cord and signal cable are securely connected. The

Power indicator LED will flash red.

2 Turn on the projector by pressing "Power" button on the control panel,

and the Power indicator LED will turn blue.

3 Turn on your source (computer, notebook, video player ,etc.). The

projector will detect your source automatically.

• If the screen displays "Lock" and "Source" icons, it means the

projector is locked onto a specific source type and there is no such

type of input signal detected.

• If the screen displays "No Signal", please make sure the signal cables

are securely connected.

• If you connect to multiple sources at the same time, use the "Source"

button on the remote control to switch between inputs.

Power button

English

Turning the projector off

1 To turn the projector off, press the power button. This message appears:

"Please press the power button again to complete the shutdown process."

Press the power button again.

2 The LED power indicator will turn RED and blink rapidly after the projector

is turned off, and the fan(s) will continue to operate for about 2 minutes to

ensure that the system cools properly. (only supported under "Instant

Resume" mode)

3 As long as the power cord remains plugged in, you can press the power

button to turn the projector immediately back on anytime during the 2-

minute shutdown process. (only supported under "Instant Resume" mode)

4 Once the system has finished cooling, the LED power indicator will stop

blinking and turn solid red to indicate standby mode.

5 It is now safe to unplug the power cord.

Warning indicators:

• "Projector Overheated. Lamp will automatically turn off soon."

This onscreen message indicates that the projector has overheated.

The lamp with automatically turn off, the projector will automatically

shut down, and the LED temp indicator will turn solid red. Contact

your local dealer or service center.

• "Fan failed. Lamp will automatically turn off soon."

This onscreen message indicates that the fan has failed. The lamp will

automatically turn off, the projector will automatically shut down,

and the LED temp indicator will blink. Contact your local dealer or

service center.

Note: Whenever the projector automatically shuts down and the

LED lamp indicator turns solid red, contact your local reseller or

service center.

English

Adjusting the Projected Image

Adjusting the Height of Projected Image

The projector is equipped with elevator feet for adjusting the height of image.

To raise/lower the image:

Use Tilt adjusting wheel to fine-tune the display angle.

Tilt adjusting wheel

English

How to optimize image size and distance

Consult the table below to find the optimal image sizes achievable when the

projector is positioned at a desired distance from the screen. Example: If the

projector is 2.0 m from the screen, good image quality is possible for image sizes

between 46" and 50".

Note: Remind as below figure, the space of 88 cm height is

required when located at 2.0 m distance.

Figure: Fixed distance with different zoom and screen size.

50"

46"

Height: 88 cm

from base to

top of image

Height:

80 cm

2.0 m

Desired Distance

English

Desired

Distance

(m)

<A>

Screen size

Top

Screen size

Top

(Min zoom) (Max zoom)

Diagonal

(inch)

<B>

W (cm) x H (cm)

From base

to top of

image (cm)

<C>

Diagonal

(inch)

<B>

W (cm) x H (cm)

From base to

top of image

(cm)

<C>

1 23 47 x 35 40 25 51 x 38 44

2 46 93 x 70 80 50 103 x 77 88

2.5 57 116 x 87 100 63 128 x 96 111

3 69 140 x 105 120 76 154 x 115 133

3.5 80 163 x 122 140 88 179 x 135 155

4 92 186 x 140 160 101 205 x 154 177

4.5 103 209 x 157 181 114 231 x 173 199

5 114 233 x 174 201 126 256 x 192 221

6 137 279 x 209 241 151 308 x 231 265

7 160 326 x 244 281 177 359 x 269 310

8 183 372 x 279 321 202 410 x 308 354

9 206 419 x 314 361 227 462 x 346 398

10 229 465 x 349 401 252 513 x 385 442

Zoom Ratio: 1.1x

English

How to get a preferred image size by adjusting

distance and zoom

The table below shows how to achieve a desired image size by adjusting either

the position or the zoom ring. For example: to obtain an image size of 50" set

the projector at a distance 2.0 m and 2.2 m from the screen and adjust the zoom

level accordingly.

Desired Distance

2.2 m

2.0 m

Height

from base to

top of image

50"

Desired

image size

English

Desired Image Size Distance (m) Top (cm)

Diagonal (inch)

<A>

W (cm) x H (cm)

Max zoom

<B>

Min zoom

<C>

From base to top of

image

<D>

30 61 x 46 1.2 1.3 53

40 81 x 61 1.6 1.7 70

50 102 x 76 2.0 2.2 88

60 122 x 91 2.4 2.6 105

70 142 x 107 2.8 3.1 123

80 163 x 122 3.2 3.5 140

90 183 x 137 3.6 3.9 158

100 203 x 152 4.0 4.4 175

120 244 x 183 4.8 5.2 210

150 305 x 229 5.9 6.6 263

180 366 x 274 7.1 7.9 315

200 406 x 305 7.9 8.7 351

250 508 x 381 9.9 10.9 438

300 610 x 457 11.9 526

Zoom Ratio: 1.1x

English

User Controls

Installation menu

The installation menu provides an onscreen display (OSD) for projector

installation and maintenance. Use the OSD only when the message "No signal

input" is displayed on the screen.

The menu options include settings and adjustments for screen size and distance,

focus, keystone correction and more .

1 Turn on the projector by pressing "Power" button on the control pad.

2 Press the menu button on the control pad to launch the OSD for projector

installation and maintenance.

3 The background pattern acts as a guide to adjusting the calibration and

alignment settings, such as screen size and distance, focus and more .

Use the up and down arrow keys to select an option, the left and right

arrow keys to adjust selected option settings, and the right arrow key to

enter a submenu for feature setting. The new settings will be saved

automatically upon exiting the menu.

4 Push the menu button anytime to exit the menu and return to the Acer

welcome screen.

English

Acer Empowering Technology

Acer Empowering Key provide four Acer unique functions, they are "Acer

eView Management", "Acer eTimer Management", "Acer ePower

Management" and "Acer e3D Management respectively.

Press " " key to launch the Onscreen display main menu to modify its

function.

When the Empowering Menu is displayed, use the " " key to select the main

menu.

Acer eView Management

"Acer eView Management" is for

display mode selection. Please refer to

Onscreen Display Menus section for

more detail.

Acer eTimer Management

"Acer eTimer Management" provides

the reminding function for

presentation time control. Please refer

to Onscreen Display Menus section for

more detail.

Acer ePower Management

"Acer ePower Management" provides

user one shortcut to save the projector

life. Please refer to Onscreen Display

section for more detail.

Acer e3D Management

"Acer e3D Management" provides the

3D functions. Please refer to Onscreen

Display Menus section for more detail.

English

Onscreen Display (OSD) Menus

The projector has multilingual OSD that allow you to make image adjustments

and change a variety of settings.

Using the OSD menus

• To open the OSD menu, press "MENU" on the remote control or control

panel.

• When the OSD is displayed, use the keys to select any item in the

main menu. After selecting the desired main menu item, press to enter

submenu for feature setting.

• Use the keys to select the desired item and adjust the settings by

using the keys.

• Select the next item to be adjusted in the submenu and adjust as described

above.

• Press "MENU" on the remote control or control panel, the screen will

return to the main menu.

• To exit OSD, press "MENU" on the remote control or control panel again.

The OSD menu will close and the projector will automatically save the new

settings.

Main menu

Sub menu

Setting

English

Color

Display Mode

There are many factory presets optimized for various types of

images.

• Bright: For brightness optimization.

• Presentation: For meeting presentation.

• Standard: For common environment.

• Video: For playing video in a bright environment.

• Game: For game content.

• Education: For education environment.

• User: Memorize user's settings.

Wall color

Use this function to choose a proper color according to the wall.

There are several choices, including white, light yellow, light blue,

pink, dark green. It will compensate the color deviation due to the

wall color to show the correct image tone.

Brightness

Adjust the brightness of the image.

• Press to darken the image.

• Press to lighten the image.

Contrast

"Contrast" controls the difference between the lightest and

darkest parts of the picture. Adjusting the contrast changes the

amount of black and white in the image.

• Press to decrease the contrast.

• Press to increase the contrast.

Saturation

Adjusts a video image from black and white to fully saturated

color.

• Press to decrease the amount of color in the image.

• Press to increase the amount of color in the image.

Tint

Adjusts the color balance of red and green.

• Press to increase the amount of green in the image.

• Press to increase the amount of red in the image.

English

Note: "Saturation" and "Tint" functions are not supported under computer

or HDMI mode.

Color

Temperature

Mode

Use this function to choose CT1, CT2 (Native), CT3, User mode.

R Gain

Adjusts the red gain for color temperature optimization.

G Gain

Adjusts the green gain for color temperature optimization.

B Gain

Adjusts the blue gain for color temperature optimization.

Gamma

Effects the representation of dark scenery. With greater gamma

value, dark scenery looks brighter.

English

Image

Projection (for X1161PA/X112/X1161PN/X1261PN series only)

• Front-Desktop: The factory default setting.

• Rear-Desktop: When you select this function, the projector

reverses the image so you can project from behind a translucent

screen.

• Rear-Ceiling: When you select this function, the projector reverses

and inverts the image at same time. You can project from behind

a translucent screen with ceiling mounted projection.

• Front-Ceiling: When you select this function, the projector inverts

the image for ceiling-mounted projection.

Keystone Adjust image distortion caused by tilting projection. (±40 degrees)(for

X1161PA/X112/X1161PN/X1261PN series only)

Projection mode (for X1161P/X1261P series only)

• Front: The factory default setting.

• Rear: Reverses the image so you can project from behind a

translucent screen.

Projection Location

(for X1161P/X1261P series only)

• Auto: Automatically adjusts projection location of image.

• Desktop

• Ceiling: Turns the image upside down for ceiling-mounted

projection.

Auto Keystone Automatically adjusts vertical image. (for X1161P/X1261P series only)

English

Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions

are not supported under HDMI or Video mode.

Maunal Keystone Adjust image distortion caused by tilting projection. (±40 degrees) (for

X1161P/X1261P series only)

<Note> The Manual Keystone function is unavailable under Auto

Keystone setting to "On".

Aspect Ratio

(for X1161P/X1261P series only)

Use this function to choose your desired aspect ratio.

• Auto: Keep the image with original width-higth ratio and maxi

mize the image to fit native horizontal or vertical pixels.

• 4:3: The image will be scaled to fit the screen and displayed using

a 4:3 ratio.

• 16:9: The image will be scaled to fit the width of the screen and

the height adjusted to display the image using a 16:9 ratio.

Sharpeness Adjusts the sharpness of the image.

• Press to decrease the sharpness.

• Press to increase the sharpness.

H. Position

(Horizontal

position)

• Press to move the image left.

• Press to move the image right.

V. Position

(Vertical position)

• Press to move the image down.

• Press to move the image up.

Frequency "Frequency" changes the projector's refresh rate to match the

frequency of your computer’s graphics card. If you can see a vertical

flickering bar in the projected image, use this function to make the

necessary adjustments.

Tracking Synchronizes the signal timing of the projector with the graphics card.

If you experience an unstable or flickering image, use this function to

correct it.

English

Setting

Closed Caption

Selects a preferred closed captioning mode from CC1, CC2, CC3,

CC4, (CC1 displays captions in the primary language in your area).

Select "Off" to turn off the captioning feature. This function is only

available when a composite video or S-Video input signal is

selected and its system format is NTSC.

<Note> Set your screen aspect ratio to 4:3. This function is not

available when the aspect ratio is "16:9" or "Auto" .

Security Security

This projector provides a useful security function for the

administrator to manage usage of the projector .

Press to change the "Security" setting. If the security function

is enabled, your must enter the "Administrator Password" first

before changing the security settings.

• Select "On" to enable the security function. The user has to

enter a password to operate the projector. Please refer to the

"User Password" section for details.

• If "Off" is selected, then the user can turn on the projector

without password.

Timeout(Min.)

Once "Security" is activated to "On", the administrator can set

timeout function.

• Press or to select the timeout interval.

• The range is from 10 minute to 990 minutes.

• When the time is up, the projector will prompt the user to

enter the password again.

• The factory default setting of "Timeout(Min.)" is "Off".

• Once the security function is enabled, the projector will

request user to enter password when switch on the projector .

Both "User Password" and "Administrator Password" can be

accepted for this dialogue.

English

User password

• Press to setup or change the "User Password".

• Press number keys to set your password on the remote control

and press "MENU" to confirm.

• Press to delete character.

• Enter the password when you see "Confirm Password"

displayed.

• The password should be between 4 and 8 characters long.

• If you select "Request password only when plugging the

power cord in.", the projector will prompt the user to enter

the password every time the power cord is plugged.

• If you select "Always request the password when turning the

projector on.", the user has to enter the password every time

when the projector is turned on.

Administrator Password

The "Administrator Password" can be used in both the "Enter

Administrator Password" and "Enter Password" dialog boxes.

• Press to change the "Administrator Password".

• The factory default of "Administrator Password" is "1234".

If you forgot your administrator password, do the following to

retrieve the administrator password:

• An unique 6-digit "Universal Password" which is printed on

the Security Card (please check accessory in the box). This

unique password is the number which will be accepted by

projector anytime no matter what the Administrator

Password is.

• If losing this security card and number, please contact with an

Acer service center.

VGA OUT (Standby) Default is "Off". Choose "On" to enable VGA OUT connection. (for

X1261P only)

Reset

• Press the button and choose "Yes" to return the

parameters on all menus to the factory default settings.

English

Management

Audio

ECO Mode Choose "On" to dim the projector lamp which will lower power

consumption, extend the lamp life and reduce noise. Choose "Off"

to return normal mode.

High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at

full speed continuously to allow for proper high altitude cooling of

the projector.

Turn Off Mode

• Instant Off: Shuts down the projector without fan cooling.

• Instant Resume: Resumes the system when the Power button

is pressed again within 2 minutes.

Auto Shutdown The projector will automatically shutdown when there is no signal

input after the allocated time. (default is 120 minutes)

Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).

Lamp Reminding Activate this function to display a reminder to change the lamp 30

hours before its expected end-of-life.

Lamp Hour Reset

Press the button and choose "Yes" to turn the lamp hour

counter to 0 hours.

Volume (for X1261P series only)

• Press to decrease the volume.

• Press to increase the volume.

Mute (for X1261P series only)

• Choose "On" to mute the volume.

• Choose "Off" to restore the volume.

English

Note: It needs correct settings on graphic card 3D application program for

correct 3D display.

Note: The SW players, such as Stereoscopic Player and DDD TriDef Media

Player can support 3D format files. You can download these three players

on web page below,

- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx

- DDD TriDef Media Player (Trial):

http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html

Note: "3D L/R Invert" is only available when 3D is enabled.

Note: There has reminder screen if 3D still enable when power on projector.

Please adjust setting depended on your purpose.

3D Choose "On" to enable DLP 3D function.

• On: Choose this item while using DLP 3D glasses, 120Hz 3D

capable graphics cards and HQFS format file or DVD with

corresponding SW player.

• Off: Turn off 3D mode.

3D Format

Adjust the 3D format to display 3D content correctly.

3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D

glasses, you may need to execute "Invert" to get best match of

left/right image sequence to get the correct image (for DLP 3D).

3D Warning Message Choose "On" to display the 3D warning message.

English

Language

Choose the multilingual OSD menu. Use the or key

to select your preferred menu language.

• Press to confirm the selection.

English

Appendices

Troubleshooting

If you experience a problem with your Acer projector, refer to the following

troubleshooting guide. If the problem persists, please contact your local reseller

or service center.

Image Problems and Solutions

# Problem Solution

1 No image appears

onscreen

• Connected as described in the "Getting Started"

section.

• Ensure none of the connector pins are bent or

broken.

• Check if the projector lamp has been securely

installed. Please refer to the "Replacing the Lamp"

section.

• Make sure you have removed the lens cap and the

projector is switched on.

2 Partial, scrolling

or incorrectly

displayed image

(for PC (Windows

2000/XP/Vista/

Windows 7))

•

Press "RESYNC" on the remote control or control panel.

• For an incorrectly displayed image:

• Open "My Computer," open the "Control

Panel," and then double-click the "Display"

icon.

• Select the "Settings" tab.

• Verify that your display resolution setting is

lower than or equal to WUXGA-RB (1920 x

1200).

• Click the "Advanced Properties" button.

If the problem still appears, change the monitor display

you are using and follow the steps below:

• Verify that the resolution setting is lower than

or equal to WUXGA-RB (1920 x 1200).

• Click the "Change" button under the

"Monitor" tab.

• Click "Show all devices". Next, select "Standard

monitor types" under the SP box, and choose

the resolution mode you need under the

"Models" box.

• Verify that the resolution setting of the

monitor display is lower than or equal to

WUXGA-RB (1920 x 1200).

English

3 Partial, scrolling

or incorrectly

displayed image

(For notebooks)

• Press "RESYNC" on the remote control or control

panel.

• For an incorrectly displayed image:

• Follow the steps for item 2 (above) to adjust

the resolution of your computer.

• Press the toggle output settings. Example:

[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],

Gateway [Fn]+[F4], IBM [Fn]+[F7], HP

[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]

• If you experience difficulty changing resolutions or

your monitor freezes, restart all equipment

including the projector.

4 The screen of the

notebook

computer is not

displaying your

presentation

• If you are using a Microsoft

Windows

based

notebook: Some notebook PCs may deactivate their

own screens when a second display device is in use.

Each has a different way to be reactivated. Refer to

your computer's manual for detailed information.

• If you are using an Apple

Mac

OS based

notebook: In System Preferences, open Display and

select Video Mirroring "On".

5 Image is unstable

or flickering

• Adjust the "Tracking" to correct it. Refer to the

"Image" section for more information.

• Change the display color depth settings on your

computer.

6 Image has vertical

flickering bar

• Use "Frequency" to make an adjustment. Refer to

the "Image" section for more information.

• Check and reconfigure the display mode of your

graphics card to make it compatible with the

projector.

7 Image is out of

focus

• Make sure the lens cap is removed.

• Adjusts the focus ring on the projector lens.

• Make sure the projection screen is within the

required distance of 3.9 to 39.0 feet (1.2 to 11.9

meters) from the projector. Refer to the "How to

Get a Preferred Image Size by Adjusting Distance

and Zoom" section for more information.

8 Image is stretched

when displaying a

"widescreen"

DVD title

When you play a DVD encoded in anamorphic or 16:9

aspect ratio you may need to adjust the following

settings:

• If you play a 4:3 format DVD title, please change the

format to 4:3 in the projector OSD.

• If the image is still stretched, you will also need to

adjust the aspect ratio. Set up the display format to

16:9 (wide) aspect ratio on your DVD player.

English

9 Image is too small

or too large

• Adjust the zoom lever on the top of the projector.

• Move the projector closer to or further from the

screen.

• Press "MENU" on the remote control. Go to "Image -

-> Aspect Ratio" and try different settings or

press"Aspect Ratio" on the remote control to adjust

directly.

10 Image has slanted

sides

• If possible, reposition the projector so that it is

centered on the screen.

• Press the "Keystone / " button on the remote

control until the sides are vertical.

• Press "MENU" on the remote control. Go to "Image -

-> Auto Keystone" and choose "Off" on the OSD, if

"Keystone" button is not available on the remote

control.

11 Image is reversed

• Select "Image --> Projection" on the OSD and adjust

the projection direction.

English

OSD Messages

# Condition Message Reminder

1 Message Fan Fail - the system fan is not working.

Projector Overheated - the projector has exceeded its

recommended operating temperature and must be allowed to

cool down before it may be used.

Replace the lamp - the lamp is about to reach its maximum

lifetime. Prepare to replace it soon.

English

Problems with the Projector

# Condition Solution

1 The projector stops responding

to all controls

If possible, turn off the projector, then

unplug the power cord and wait at least 30

seconds before reconnecting power.

2 Lamp burns out or makes a

popping sound

When the lamp reaches the end of its useful

life, it will burn out and may make a loud

popping sound. If this happens, the projector

will not turn on until the lamp module has

been replaced. To replace the lamp, follow

the procedures in the "Replacing the Lamp"

section.

English

LED & Alarm Definition Listing

LED Messages

Message

Power LED

Red Blue

Input Power Plug Flash ON to OFF 100ms --

Standby V --

Power button ON -- V

Lamp retry -- Quick Flashing

Power off (Cooling state) Quick Flashing --

Power button OFF:

Cooling completed;

Standby Mode

V--

Error (Thermal Failure) Quick Flashing RED and Steady BLUE by returns

Error (Fan lock) Quick Flashing RED and Steady BLUE by returns

Error (Lamp breakdown) Quick Flashing BLUE and Steady RED by returns

Error (Color Wheel fail) Quick Flashing BLUE and Steady RED by returns

English

Replacing and cleaning the dust filters

Replacing the dust filters

1 Turn the projector off then unplug the power cord.

2 Pull the both sides dust filters out. (Illustration #1)

3 Clean or replace the dust filter.

4 To put the dust filters back, reverse the previous step.

Cleaning the dust filters

Clean the dust filters after every 1000 hours of use. If they are not cleaned

periodically, they can become clogged with dust, preventing proper ventilation.

This can cause overheating and damage the projector. (Normally 1000 hours is

recommended, clean period will be depending on actual environment)

Please find following steps for cleaning procdure:

1 To clean the dust filters, use a small vacuum cleaner designed for

computers and other office equipments. It also can be cleaned by water.

(Illustration #2)

2 If the dirt is difficult to remove or the filter is broken, please contact your

local dealer or service center to obtain a new filter.

(Illustration #1)

Dust Filter

(Illustration #2)

English

Replacing the Lamp

Use a screwdriver to remove the screw(s) from the cover, and then pull out the

lamp.

The projector will detect the lamp life. You will be shown a warning message

"Lamp is approaching the end of its useful life in full power operation.

Replacement Suggested!" When you see this message, change the lamp as soon

as possible. Make sure the projector has been cooling down for at least 30

minutes before changing the lamp.

Warning: The lamp compartment is hot! Allow it to cool down

before changing the lamp.

To Change the Lamp

1 Turn off the projector by pressing the Power button.

2 Allow the projector at least 30 mins to cool down.

3 Disconnect the power cord.

4 Use a screwdriver to remove the screws from the cover. (Illustration #1)

5 Push up and remove the cover.

6 Remove the two screws that secure the lamp module (Illustration #2) and

pull up the lamp bar.(Illustration #3)

7 Pull out the lamp module by force. (Illustration #4)

To replace the lamp module, reverse the previous step.

Warning: To reduce the risk of personal injury, do not drop the

lamp module or touch the lamp bulb. The bulb may shatter and

cause injury if it is dropped.

English

Ceiling Mount Installation

If you wish to install the projector using a ceiling mount, please refer to the

steps below:

1 Drill four holes into a solid, structurally sound part of the ceiling, and

secure the mount base.

Note: Screws are not included. Please obtain the appropriate

screws for your type of ceiling.

2 Secure the ceiling rod using the appropriate type of four-cylinder screws.

8.4

130 mm

49.9

Short Rod

Ceiling Mount Base

- Attach to ceiling

Screw Type A

50 mm length / 8 mm diameter -

Long Rod

Extension Rod

Long Cylinder Cap

Tightening Screw

Medium Rod

Allen Key

- For tightening/loosening

English

3 Use the appropriate number of screws for the projector size to attach the

projector to the ceiling mount bracket.

Note: It is recommended that you keep a reasonable space

between the bracket and the projector to allow for proper heat

distribution. Use two washers for extra support, if deemed

necessary.

4 Attach the ceiling bracket to the ceiling rod.

Smaller Washer

Projector Bracket

Large Washer

upports projector and allows

for adjustments

Screw Type B

Spacer

- For heat dissipation

Screw Type A

50 mm length/

8 mm diameter

Large cylinder cap

Allen Key

Tightening Screw

- For tightening/loosening

English

5 Adjust the angle and positioning as necessary.

Note: The appropriate type of screw and washer for each model is

listed in the table below. 3 mm diameter screws are enclosed in

the screw pack.

Models Screw Type B Washer Type

Diameter (mm) Length (mm) Large Small

X1161P/X1161PA/

X1161PN/X112/

X1261P/X1261PN

325VV

Tightening Screw

Allen Key

Tightening Screw

Allen Key

82.30 mm

15.00 mm

95.00 mm

SCREW SPEC. M3 x 25 mm

English

Specifications

The specifications listed below are subject to change without notice. For final

specs, please refer to Acer's published marketing specifications.

Projection system

DLP

Resolution X1161P/X1161PA/X1161PN/X112: Native: SVGA (800 x

600) , Maximum: UXGA (1600 x 1200), WSXGA+

(1680x1050), 1080p(1920x1080), WUXGA-RB (1920 x

1200)

X1261P/X1261PN: Native: XGA (1024 x 768),

Maximum: UXGA (1600 x 1200), WSXGA+

(1680x1050), 1080p(1920x1080), WUXGA-RB (1920 x

1200)

Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and

VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,

WXGA, WXGA+, WSXGA +

Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/

K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,

576p), SDTV (480i, 576i)

Aspect ratio 4:3 (native), 16:9

Displayable colors 16.7 million colors

Projection lens F/ 2.41 - 2.55, f = 21.79 mm - 23.99 mm, 1.1X manual

zoom lens

Projection screen size (diagonal) 27" (70 cm) - 300" (762 cm)

Projection distance 3.9' (1.2 m) - 39.0' (11.9 m)

Throw ratio 50"@2m (1.95 - 2.15:1)

Horizontal scan rate 30k - 100 kHz

Vertical refresh scan rate 50-120 Hz

Lamp type 190W user-replaceable lamp

Keystone correction

±40 degrees

Audio Internal speaker with 2 W output (X1261P)

Weight 2.2Kg (4.85 Ibs)

Dimensions (W x D x H) 268 mm x 192 mm x 80 mm (10.6" x 7.6" x 3.1")

Digital Zoom 2X

Power supply AC input 100 - 240 V auto-switching power supply

Power consumption Normal mode: 235W ± 10% @ 110VAC

ECO mode: 197W ± 10% @ 110VAC

Standby mode < 0.5W

Operating temperature 0ºC to 40ºC / 32ºF to 104ºF

English

* Design and specifications are subject to change without notice.

Standard package contents

• AC power cord x1

• VGA cable x1

• Remote control x1

• Battery x1 (for remote control)

• User's guide (CD-ROM) x1

• Quick start guide x1

• Security card x1

• Carrying case x1 (Optional)

I/O connectors X1261P X1161PN/X1261PN X1161P/X1161PA/X112

Power socket V V V

USB (for remote

computer control)

XV V

VGA IN V V V

S-Video V X V

Composite video V X V

RS232 V X X

VGA output V X X

3.5 mm audio jack

input

VX X

English

Compatibility modes

VGA Analog

1 VGA Analog - PC Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

VGA 640x480 60 31.47

640x480 72 37.86

640x480 75 37.50

640x480 85 43.27

640x480 119.51 61.60

SVGA 800x600 56 35.20

800x600 60 37.88

800x600 72 48.08

800x600 75 46.88

800x600 85 53.67

800x600 119.85 77.20

XGA 1024x768 60 48.36

1024x768 70 56.48

1024x768 75 60.02

1024x768 85 68.67

1024x768 119.804 98.80

SXGA 1152x864 70 63.80

1152x864 75 67.50

1152x864 85 77.10

1280X1024 60 63.98

1280X1024 72 77.90

1280X1024 75 79.98

1280X1024 85 91.15

QuadVGA 1280x960 60 60.00

1280x960 75 75.00

SXGA+ 1400x1050 60 65.32

UXGA 1600x1200 60 75.00

PowerBook G4 640x480 60 31.50

640x480 66.6(67) 35.00

800x600 60 37.88

1024x768 60 48.36

1152x870 75 68.68

1280x960 75 75.20

i Mac DV (G3) 1024x768 75 60.30

English

2 VGA Analog - Extended Wide timing

3 VGA Analog -Component Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

WXGA 1280x768 60 47.78

1280x768 75 60.29

1280x768 85 68.63

1280x720 60 44.80

1280x800 60 49.60

1440x900 60 55.90

1680x1050 60 65.30

1366x768 60 47.71

1920x1080-RB 60 66.60

UWXGA 1920x1200-RB 60 (59.95) 74.04

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

480i 720x480 59.94 (29.97) 15.70

480p 720x480 59.94 31.47

576i 720x576 50(25) 15.60

576p 720x576 50 31.25

720p 1280x720 60 45.00

720p 1280x720 50 37.50

1080i 1920x1080 60(30) 33.75

1080i 1920x1080 50(25) 28.10

1080p 1920x1080 60 67.50

1080p 1920x1080 50 56.25

1080p 1920x1080 24 27.00

1080p 1920x1080 23.97 26.97

Horizontal scan rate:

30-100 kHz

Vertical scan rate:

50-120 Hz

Max. pixel rate:

165 MHz

English

Regulations and safety notices

FCC notice

This device has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This device generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this device does cause harmful interference to radio or television

reception, which can be determined by turning the device off and on, the user

is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables

to maintain compliance with FCC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.) certified to

comply with the Class B limits may be attached to this equipment. Operation

with non-certified peripherals is likely to result in interference to radio and TV

reception.

Caution

Changes or modifications not expressly approved by the manufacturer could

void the user's authority, which is granted by the Federal Communications

Commission, to operate this device.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

English

Remarque à l'intention des utilisateurs canadiens

Cet appareil numérique de la classe B est conforme a la norme NMB-003 du

Canada.

Declaration of Conformity for EU countries

Acer hereby declares that this projector series is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Compliant with Russian regulatory certification

Radio device regulatory notice

Note: The regulatory information below is for models with

wireless LAN and/or Bluetooth only.

General

This product complies with the radio frequency and safety standards of any

country or region in which it has been approved for wireless use. Depending on

configurations, this product may or may not contain wireless radio devices (such

as wireless LAN and/or Bluetooth modules).

Canada — Low-power license-exempt radio

communication devices (RSS-210)

a Common information

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference

that may cause undesired operation of the device.

b Operation in 2.4 GHz band

To prevent radio interference to the licensed service, this device is

intended to be operated indoors and installation outdoors is subject

to licensing.

List of applicable countries

This device must be used in strict accordance with the regulations and constraints in the

country of use. For further information, please contact the local office in the country of use.

Please see http://ec.europa.eu/enterprise/rtte/implem.htm

for the latest country list.

Acer Incorporated

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,

New Taipei City 221, Taiwan

 

'HFODUDWLRQRI&RQIRUPLW\



:H

$FHU,QFRUSRUDWHG

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan

Contact Person: Mr. RU Jan, e-mail:ru_jan@acer.com.tw

And,

$FHU,WDO\VUO

Via Lepetit, 40, 20020 Lainate (MI) Italy

Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it

Hereby declare that:

3URGXFW 3URMHFWRU

7UDGH1DPH $FHU

0RGHO1XPEHU '69'69'1;'1;

0DFKLQH7\SH ;3;3$;31;

;3

;31VHULHV

Is compliant with the essential requirements and other relevant provisions of the following EC

directives, and that all the necessary steps have been taken and are in force to assure that

production units of the same product will continue comply with the requirements.

(0&'LUHFWLYH(&DVDWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ

KDUPRQL]HGVWDQGDUGV

-. EN55022, AS/NZS CISPR22, Class B

-. EN55024

-. EN61000-3-2 Class A

-. EN61000-3-3

/RZ9ROWDJH'LUHFWLYH(&DVDWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ

KDUPRQL]HGVWDQGDUG

-. EN60950-1



5R+6'LUHFWLYH(&RQWKH5HVWULFWLRQRIWKH8VHRIFHUWDLQ+D]DUGRXV

6XEVWDQFHVLQ(OHFWULFDODQG(OHFWURQLF(TXLSPHQW

-. The maximum concentration values of the restricted substances by weight in homogenous

material are:

'LUHFWLYH(&ZLWKUHJDUGWRHVWDEOLVKLQJDIUDPHZRUNIRUWKHVHWWLQJ

RIHFRGHVLJQUHTXLUHPHQWVIRUHQHUJ\UHODWHGSURGXFW

Lead 0.1% Polybrominated Biphenyls (PBB’s) 0.1%

Mercury 0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%

Hexavalent Chromium 0.1% Cadmium 0.01%

Acer Incorporated

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,

New Taipei City 221, Taiwan

7KHVWDQGDUGVOLVWHGEHORZDUHDSSOLHGWRWKHSURGXFWLIEXLOWZLWK:/$1

PRGXOHRUZLUHOHVVNH\ERDUGDQGPRXVH

577('LUHFWLYH(&DV DWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ

KDUPRQL]HGVWDQGDUG

z$UWLFOHD+HDOWKDQG6DIHW\



-. EN60950-1

-. EN62311 

z$UWLFOHE(0&

-. EN301 489-1

-. EN301 489-17

z$UWLFOH6SHFWUXP8VDJHV

-. EN300 328

-. EN301 893 (Applicable to 5GHz high performance RLAN).

<HDUWREHJLQDIIL[LQJ&(PDUNLQJ

_______________________________ 1RY -

RU Jan/Sr. Manager Date

Regulation Center, Acer Inc.

Acer America Corporation

333 West San Carlos St.,

Suite 1500

San Jose, CA 95110

U. S. A.

7HO   254-298-4000

)D[   254-298-4147

ZZZ DFHU  FRP

Federal Communications Commission

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

The following local Manufacturer / Importer is responsible for this declaration:

Product: DLP Projector

Model Number: DSV0008/DSV1144/DNX0009/DNX1143

Machine Type: X1161P/X1161PA/X1161PN/X112/X1261P/

X1261PN series

Name of Responsible Party: Acer America Corporation

Address of Responsible Party: 333 West San Carlos St.

Suite 1500

San Jose, CA 95110

U. S. A.

Contact Person: Acer Representative

Phone No.: 254-298-4000

Fax No.: 254-298-4147

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Acer X1161PN in the language / languages: English as an attachment in your email.

The manual is 4,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Acer X1161PN Manual

Product: