721669
52
Zoom out
Zoom in
Previous page
1/54
Next page
51
18
Ghosting (a double image) occurs
without the image appearing in
3D.
Check that you are using 3D LCD shutter glasses that
support the DLP
®
Link™ system.
- Be sure to use 3D LCD shutter glasses that support the
DLP
®
Link™ system.
Check that the shutters on the 3D LCD shutter glasses
are working properly.
- Turn the 3D LCD shutter glasses off and then on again.
- Check the batteries of the 3D LCD shutter glasses.
- Check that the 3D LCD shutter glasses are set to 3D
viewing mode.
Some 3D LCD shutter glasses are equipped with a
special viewing mode (such as "dual view mode") in
addition to the normal 3D viewing mode. See the
operation manual of your 3D LCD shutter glasses.
Check the settings of the projector.
- Check 3D Mode setting.
- Use "3D Sync Invert" to change the setting.
Check whether a signal that is not supported is being
input.
- Configure your 3D application at the correct resolution
and refresh rate.
Make sure you are running your 3D application in
resolutions that support 3D. To support 3D, your 3D
application must be configured to run at the correct
settings for this projector.
For details on the supported signals, see "3D Supported
Signals" of the Compatibility Chart.
If the projector is connected to a computer for 3D image
playback, check that a stereoscopically-enabled
application is being used.
- Use the applicable software.
- Set the applicable software to the field sequential
format.
Check that there are no obstructions between the screen
and the 3D LCD shutter glasses.
- Remove any obstructions.
Any obstructions may cause the glasses not to function
properly causing the lenses to flicker or turn off. Do not
place your hand or other objects in front of the 3D control
signal sensor on the glasses.
Check whether there is a source of high intensity lighting
nearby.
- Block the light or turn it off.
High intensity lighting can interfere with communication
between the 3D LCD shutter glasses and the screen
resulting in some flicker.
Check whether two or more projectors are projecting 3D
images at the same time.
- Use only one projector at a time.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Acer FL-440 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Acer FL-440 in the language / languages: English as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info