755219
29
Zoom out
Zoom in
Previous page
1/82
Next page
7
UK
Manual
If the manual variant is programmed, you now see the
following on the LCD display:
The alarm centre now generates a constant signal tone (if
you hear no constant tone, read the section “Open zones”
on page 7). You can now leave the object. The alarm
system is not activated until you close the entry/exit zone
and close a contact connected with the control unit. The
alarm system is activated seven seconds after this contact
is activated.
IMPORTANT: The signal tone is generated only if this is
set in the program menu.
6.1.1 Display when active
After the delay time expires, the alarm centre is activated
and emits a double tone to confirm successful activation,
irrespective of how it is programmed. The control unit
display shows:
IMPORTANT: This display appears only if this is set in
the program menu.
In the program menu, you can make the setting so that
the display disappears after about 30 seconds and the
date and time are shown instead.
6.1.2 Open zones
If the alarm centre cannot be activated because a zone is
still open, it issues a double tone. It then displays the
zone(s) preventing activation of the alarm system.
Close the open zones and activate the alarm system
again.
If a zone is opened during the delay time, the constant
tone is interrupted and you hear a pulsed signal tone.
These zones are shown on the LCD display. The zones
must be closed within the exit delay time, otherwise there
is an internal alarm and the system is not activated.
Confirm this alarm by entering a valid user code. The
control unit LCD displays the zones preventing activation
of the alarm system.
Before you can activate the alarm system again, you have
to reset the alarm centre. To do this, enter a valid user
code:
IMPORTANT: If defined in the program menu, you have
to enter a program code (installer code) to
reset the alarm centre.
Some zones are allowed to be open at the moment of
activation. Despite the open zones, the alarm system
starts counting down the exit delay time, but instead of a
constant tone, it issues a pulsed signal tone. You must
close these zones within the delay time, otherwise there
will be an internal alarm as described above.
Zone types that are allowed to be open are: entry/exit and
entry to follow zones.
6.1.3 Abort
You can cancel the exit delay by entering a valid user
code.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus Terxon SX - AZ4111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus Terxon SX - AZ4111 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Terxon SX - AZ4111

Abus Terxon SX - AZ4111 Installation Guide - English, German, Dutch, Danish, French - 484 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info