Manual Abus Terxon LX - AZ4200 (page 106 of 116) (English)

755222

106

Zoom out

Zoom in

1/116

100

In the scope of delivery, there are 2.2kOhm and

4.7kOhm resistors (2.2kOhm: red, red, red, gold,

and 4.7kOhm: yellow, violet, red, gold).

If you choose the DEOL method, you need 2

lines for wiring each zone. Note that the voltage

supply of the sensor requires two additional lines.

We recommend that you use a zone with only

one sensor since you can then precisely identify

the triggering sensor if there is an alarm.

Whichever method you choose, note that the line

resistance must not exceed 100 Ohm.

1.30 Connections for anti-masking zones

Some sensors are fitted with a so-called anti-

masking function, which monitors whether the

lens is covered or not.

They can e wired in two ways. In the first method,

the open/close contact is connected to a

separate, masking-type zone. Here, two zones

are needed: one to monitor the masking state,

and another for alarm and tamper. In the second

method, a special resistor (normal 2K2) is used

for masking the sensor and connected with alarm

and tamper to a zone. The zone must be wired

as in the figure below. See the figure for

resistance values. The zone must also be

assigned the “masking” zone attribute.

1.31 Connecting auxiliary modules

The 8-zone wired auxiliary module and the 8-

zone radio auxiliary module are connected to the

4-wire bus as follows:

As with the alarm centre, you can select NC

(without resistor) or DEOL (with two resistors) for

the zone connection.

1.32 Addressing auxiliary modules

Every auxiliary module must have a unique

address in order to be recognised by the alarm

centre via the bus. No two auxiliary modules on

the same bus must have the same address. Use

the jumper to assign a unique address to the

module. For more information, read the operating

instructions of the auxiliary.

1.33 Walk test

For the walk test function, output OP3 must be

programmed accordingly (see page 31). If the

user activates the walk test function, the LED for

detecting a movement is activated on the sensor.

1.34 Alarm memory sensor

For the alarm memory function, e.g., for motion

sensors, an output must be programmed

accordingly (see page 31). The sensor that first

triggered in a line can store and signal this.

Wired extension

Terxon L

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Abus Terxon LX - AZ4200 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Terxon LX - AZ4200

Abus Terxon LX - AZ4200 User Manual - English - 16 pages

Abus Terxon LX - AZ4200 Installation Guide - German - 31 pages

Abus Terxon LX - AZ4200 User Manual - German - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Abus Terxon LX - AZ4200 Manual

Product: