755222
105
Zoom out
Zoom in
Previous page
1/116
Next page
Appendix IV – Wiring Information
99
LED9 (state of relay 2): Lights when relay 1 is
activated.
LED10 (state of transistor output 3): Lights
when transistor output 3 is activated.
LED11 (state of transistor output 4): Lights
when transistor output 4 is activated.
LED12 (state of strobe output): Lights when
the strobe output is activated.
LED12 (state of bell output): Lights when the
bell output is activated.
LED14: (state of transistor output 5): Lights
when transistor output 5 is activated.
1.28 Fuses
The alarm centre board contains the following
fuses that reset automatically.
Note that voltage must be removed
completely to make a reset!
F1: Battery charge circuit
F2: Output 12V DC bus 1
F3: Output 12V DC bus 2
F4: External alarm sounder
F5: 12V DC output for supplying external devices
F6: Bell output
1.29 Resistors
The alarm centre has 8 connection blocks for
zones. Two or more sensors can be connected to
each zone. Either DEOL or NC can be used for
wiring the zones.
Method 1: Zone closed NC (no resistor inserted)
This is the factory default method. If you use
sensors with normally open contacts, select
“Invert” under the zone attributes. In this variant,
the system can only detect whether the zone is
opened and it always registers an opening as an
alarm in this zone. The tamper contacts must be
connected to the alarm contacts of the respective
tamper zones. For wiring with this method, you
need 4 lines. Note that the voltage supply of the
sensor requires two additional lines.
Method 2: Zone closed by resistors (2 resistors
used)
In Variant B, the tamper contact and alarm
contact are monitored in one zone. In the event
of a change of resistance, the alarm station can
distinguish whether it is a real alarm or tampering.
The first figure shows the connection of just one
sensor to a zone. In the lower figure, two sensors
are serially connected to a zone. Note that you
can choose different variations of resistance
values.
Alarm resistance (±5%) Series resistance (±5%)
4.7kOhm 2.7kOhm
1kOhm 1kOhm
4.7kOhm 4.7kOhm
2.7kOhm 2.7kOhm
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus Terxon LX - AZ4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus Terxon LX - AZ4200 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Terxon LX - AZ4200

Abus Terxon LX - AZ4200 User Manual - English - 16 pages

Abus Terxon LX - AZ4200 Installation Guide - German - 31 pages

Abus Terxon LX - AZ4200 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info