755213

Abus Secvest V3 - FUAA50510 Manual

3
Zoom out
Zoom in
Previous page
1/82
Next page
Secvest
User guide
V3.00.04
22
Contents
English
1. Scope of delivery .................................................................................................. 4
2. General ............................................................................................................. 5
2.1 Safety information ........................................................................................... 5
2.2 Information on user guide ................................................................................ 6
2.3 Warranty ....................................................................................................... 6
2.4 Disposal ........................................................................................................ 6
2.5 Declaration of conformity .................................................................................. 6
3. Installation example ............................................................................................. 8
4. Overview of the system and control panel ................................................................. 9
5. Overview of the numerical keypad ........................................................................... 10
6. Secvest display .................................................................................................... 12
7. Menu navigation and operation .............................................................................. 13
8. Arming and disarming the system ........................................................................... 13
8.1 Arming/disarming keys ..................................................................................... 13
8.2 Graphical display of arming/disarming on the display ............................................. 14
8.3 Arming/disarming via the quick arm keys ............................................................. 14
8.4 Arming via the user code .................................................................................. 14
8.5 Arming sub-areas ........................................................................................... 16
8.6 Individual sub-areas ....................................................................................... 17
8.7 Internal arming .............................................................................................. 17
8.8 Internal arming via chip key ............................................................................. 18
8.9 Internal arming via remote control ..................................................................... 18
8.10 Arming via wireless control panel ...................................................................... 18
8.11 Arming via remote control ................................................................................ 18
8.12 Arming via chip key ........................................................................................ 19
8.13 Arming via delay times .................................................................................... 19
8.14 Preventing arming of the system ....................................................................... 20
9. Responding to an alarm ........................................................................................ 21
9.1 Alarm types .................................................................................................... 21
9.2 Alarm forwarding ............................................................................................ 22
9.2.1 Alarm forwarding via telephone .................................................................. 22
9.2.2 Alarm forwarding to a monitoring station ..................................................... 23
9.2.3 Alarm forwarding via email ........................................................................ 23
9.2.4 Alarm forwarding via text message .............................................................. 23
9.2.5 Alarm forwarding in the event of a personal or medical emergency .................... 23
10. User menu ........................................................................................................ 24
10.1 Users .......................................................................................................... 26
10.2 Voice memo ................................................................................................ 27
10.3 Hide zones .................................................................................................. 27
10.5 System conguration ..................................................................................... 28
10.5.1 Functions .............................................................................................. 28
10.5.2 Date & time .......................................................................................... 33
10.5.3 Edit outputs .......................................................................................... 34
10.5.4 Remote controls ..................................................................................... 35
10.5.5 Volume settings .................................................................................... 35
10.5.6 Web access ........................................................................................... 35
10.5.7 Remote updates ..................................................................................... 36
10.5.8 Time schedules active/inactive .................................................................. 36
10.6 Contacts ..................................................................................................... 36
Contents
3|22
10.7 Test............................................................................................................ 38
10.7.1 Walk test ............................................................................................... 38
10.7.2 Sirens & sounders ................................................................................... 39
10.7.3 Door locks ............................................................................................. 39
10.7.4 Outputs ................................................................................................ 39
10.7.5 Chip key ............................................................................................... 39
10.7.6 Remote controls ..................................................................................... 40
10.7.7 Emergency buttons .................................................................................. 40
10.7.8 Telephone call ....................................................................................... 40
10.8 Log ........................................................................................................... 40
10.9 Information ................................................................................................ 41
10.9.1 Alarm panel .......................................................................................... 41
10.9.2 Communication ..................................................................................... 42
11. Advanced system operation ................................................................................... 44
11.1 Remote control .............................................................................................. 44
11.2 Wireless cylinder lock (“Secvest key”) ................................................................. 44
11.3 Additional door lock (FU7010/7025E) ................................................................... 44
11.4 Operation via telephone .................................................................................. 45
12. Operation via web (app/browser) ............................................................................ 46
12.1 Operation via web browser .............................................................................. 46
12.2 Operation via app.......................................................................................... 46
13. Operation via web browser.................................................................................... 47
13.1 Setting the Secvest IP address ........................................................................... 48
13.2 Overview of the web interface .......................................................................... 48
13.3 Arming & disarming ....................................................................................... 49
13.3.1 Hide zones ........................................................................................... 50
13.4 Additional web interface options ...................................................................... 51
13.5 Conguring Secvest “time schedules” ................................................................ 54
13.6 Datasets ...................................................................................................... 57
13.7 Exceptions ................................................................................................... 57
14. Terms and denitions .......................................................................................... 58
15. Technical data .................................................................................................... 65
16. Troubleshooting ................................................................................................. 78
44
1. Scope of delivery
Dear Customer,
Thank you for purchasing this SECVEST wireless alarm panel. This device is built with state-of-the-art technology
and it complies with current domestic and European regulations. Conformity has been proven, and all related
certications are available from the manufacturer on request (www.abus.com). To guarantee safe operation,
it is essential that you observe the instructions in this user guide. If you have any questions, please contact
your specialist dealer.
Everything possible has been done to ensure that the content of these instructions is correct. However,
neither the author nor ABUS Security-Center GmbH & Co. KG can be held liable for loss or damage caused by
incorrect or improper installation and operation or failure to observe the safety instructions and warnings.
No liability can be accepted for resulting damage. No part of the product may be changed or modied in
any way. If you do not follow these instructions, your warranty claim becomes invalid. Subject to technical
modifications.
© ABUS Security-Center GmbH & Co. KG, 12/2017.
We reserve the right to make changes to this manual without prior notice. This wireless alarm panel is
suitable for use in combination with detectors and sounders for the protection of property, such as your
company, home, garage, garden shed and holiday home.
1. Scope of delivery
The following components are included in the scope of delivery for your new Secvest product:
• Wireless alarm panel
• Rechargeable battery
• Quickstart guide
•Mounting material
3 x screws
3 x screw anchors
Battery
Quickstart
guide
1
4
7
*
2
5
8
0
3
6
9
#
3x 3x
5|44
2. General
2.1 Safety information
The alarm panel and its connected components must not under any circumstances come into contact with
water, such as in the bathroom. Using the device for purposes other than those described may damage this
product and may also lead to hazards such as short circuits, re or electric shock. The power supply unit is
suitable for operation on the public electrical grid with 230VAC/50Hz. No part of the product may be changed
or modied in any way. Connection to the public electrical grid is subject to your country’s specic regulations.
Please seek information on these regulations before connecting the product to the public grid. Only use the
device for the purpose for which it was built and designed. Any other use is considered unintended.
During the initial set-up of the alarm control panel there is neither a predefined standard installer code
nor a predefined standard administrator code. These need to be individually assigned in the set-up wizard.
Aer the initial start-up please change the default installer name (code = name) as well as the default
administrator name (code = name) to secure user names. When adding users, please make sure you are
careful about how log-in details are handled.
Handling log-in details for your security systems
Basics:
• User names and codes for logging into security systems should be known only by the legal owners and
never given out to unauthorised parties.
• If you have to pass this information on via email, please take care to send the user name and code in
two separate emails.
• User names and codes should be changed regularly.
Standards:
• User names must be at least eight characters long.
• They should ideally contain characters from at least three of the following categories:
uppercase letters, lowercase letters, special characters, and numbers.
• User names should never contain your own name, the name of a family member, your pet, your best
friend or your favourite celebrity, or your hobby or date of birth.
• Avoid using user names and codes that you use on other websites or that could be easily guessed by
others.
• Your user name should not be able to be found in a dictionary and should never be a product name.
• It should not be a conventional series of characters, a repeated pattern or a keyboard pattern, such as
asdfgh or 1234abcd.
• You should avoid only using numbers at the end of your user name or using one of the more typical
special characters (!). ? #) at the beginning or end to compensate for an otherwise simple user name.
• User names and codes should be changed at least every 180days.
• New user names and codes should not be identical to any of the three combinations used before them.
• New user names and codes should dier from user names and codes that have been used before by at
least two characters.
• Macros and scripts should not be used to input user names and codes.
2. General
6
Safety information
2.2 Information on user guide
These instructions contain important installation and operation information. Follow the directions and
instructions in this user manual to ensure safe operation. Store this manual in a safe place for future reference.
This manual constitutes part of the device. If you pass the device on to third parties, please remember to
include this manual.
Note
S/W 3.00.04
This manual relates to soft ware version 3.00.04 and all other previously published soft ware versions. All
new features that are only valid from a certain soft ware version are marked accordingly, e.g. >=2.00.00. All
other features that are valid up to a certain soft ware version are also marked accordingly, e.g. <2.00.00.
2.3 Warranty
In the event of a warranty claim, the original receipt with the date of purchase and a short written description
of the problem must be supplied with the product. If you discover a defect on your wireless alarm panel
which existed at the time of purchase, contact your dealer directly within the  rst two years.
2.4 Disposal
Dispose of the device in accordance with EU Directive 2002/96/EC – WEEE (Waste Electrical and Electronic
Equipment). If you have any questions, please contact the municipal authority responsible for disposal. You
can get information on collection points for waste equipment from your local authority, from local waste
disposal companies or your dealer, for example.
2.5 Declaration of conformity
ABUS Security-Center hereby declares that this type of wireless system FUAA50xxx, complies with RED
Directive 2014/53/EU. The full EU Declaration of Conformity text can be found at: www.abus.com Artikelsuche
FUAA50xxxx/Downloads
The Declaration of Conformity can also be obtained from the following address:
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5, 86444 A n g, GERMANY
2. General
7|6
88
3. Installation example
The following provides a simple installation example to show some important basic applications for the
alarm system. The example focuses on a single-family detached home. A representative installation has been
illustrated here, as an example of how it could be implemented in a similar or more advanced form for your
property as well:
The following components are installed in this example:
18 x magnetic contacts at the windows and doors
21 x Secvest key (wireless cylinder lock) at the doors for easy arming/disarming
31 x Secvest alarm panel
42 x motion detectors indoors
51 x wireless outdoor siren under the roof
61 x wireless control panel in the bedroom
71 x info module in the hallway
Perimeter protection: Protects against all possibility of access from outside (windows, doors, etc.).
Analarm is triggered as soon as someone gains access to the property.
Interior protection: Predominantly used as a second line of defence, armed when the occupants of the
building are away so that the perimeter protection acts as the rst alarm and the
interior protection as additional security against intruders.
Internal arming: If you are in the building you can arm just the detectors for the perimeter protection.
The motion detectors indoors remain disabled in this case.
External arming: All available detectors on the premises are enabled.
An overview of all important terms concerning the alarm panel and alarm system can be found in the
appendix under "Terms and denitions".
3. Installation example
1
1
1
1
1
1
1
1
2
3
44
5
7
7
9|88
4. Overview of the system and control panel
1
4
7
*
2
5
8
0
3
6
9
#
4. Overview of the system and control panel
1Graphical display for status, menus and additional information
2Keys for menu navigation (see "Menu navigation")
3Quick disarm key for disarming the complete system (code entry required)
4Microphone opening
5Proximity chip key reader area
6Numerical keypad (see following page)
7"Internal arm" key for quick arming of perimeter protection
8Quick arm key for arming the complete system
2
1
3
4
6
5
7
8
10
5. Overview of the numerical keypad
The numerical keypad is used to enter values in certain menus. Letters and special characters are also stored
on the keypad for entering things like user names or email addresses.
1
4
7
*
2
5
8
0
3
6
9
#
The numerical keypad can be used to input various information. For
example, a name can be entered when creating a new user (see "Users").
The letters are not printed on the numerical keypad in order to provide
a better overview during day-to-day operation. Letters are entered
according to the legend provided below.
In addition to data input, numerical keys 1/3, 4/6, 7/9 and the */#
keys are used for quick arming. If the quick arming function using key
combinations is enabled (ask your specialist installation contractor),
both keys of each key pair must be pressed at the same time. The
following alarm options are available:
1
4
7
*
2
5
8
0
3
6
9
#
D, E, F, È, É, Ê, Ë, Ę, 3
J, K, L, Ł, 5
M, N, O, Ø, Ö, Ô,
OE, Ń, Ó, Ñ, 6
G, H, I, Î, Ï, Ğ, İ, 4
A, B, C, Æ, Å, Ä,
À, Â, Ç, Ą, Ć, 2
1
W, X, Y, Z, Ÿ, Ź, Ż, 9
P, Q, R, S, Ś, Ş, 7
, ( ) : . - ! &
@ + _ * # 0
T, U, V, Ü, Ù, Û , 8
5. Overview of the numerical keypad
11|10
5. Overview of the numerical keypad
Fire alarm
Press both re alarm keys at the same time to manually trigger a re alarm (for example, if you notice a re
and wish to warn others in the household). The system beeps twice in cycles as a way of providing acoustic
feedback.
Panic alarm
Press both panic keys to trigger a manual panic alarm (for example, if an intruder enters the property while
you are at home). When the keys are pressed, either an acoustic alarm sounds (tone like for an intruder
alarm) or a silent alarm is triggered, depending on your agreement with the specialist installation contractor.
A silent alarm is transmitted to a monitoring station via the integrated dialler, for example.
Medical emergency call
Press both of these keys to trigger a medical emergency call. If there is a potential medical problem (such
as asudden feeling of faintness) this call sends a message to a rescue coordination centre specialised in
handling medical emergencies.
Nursing emergency call
If a vulnerable person resides in your home and requires help, this key combination triggers a related
emergency call. In this case a rhythmic beep sounds from the alarm panel so that other people in the home
are informed that there is a problem.
These and other functions must be set up by a specialist installation contractor as required. The alarms
listed above must be congured by the specialist installation contractor as required when the alarm
panel is installed.
Note:
You are using the touch-front. The backlighting is set to “WHEN active” and the backlighting is dark.
The illumination is rst turned on when a button is pressed (rst touch). No other action results from a
“rst touch”. From the second touch on, the keypad functions as normal.For details, see section 10.5.1
Functions- Backlighting
1212
6. Secvest display
6. Secvest display
1
Voice message This symbol is displayed when a voice message has been recorded (for example,
areminder from another user). A er the alarm panel has been disarmed the user receives the
following audio message: "You have a message". The message can then be played back and deleted
ifdesired.
2Symbol for activity monitoring. This symbol is only displayed when activity monitoring is active.
This function is used for monitoring vulnerable persons and must be con gured by the specialist
installation contractor.
3Display of time and date
4Display of the status of up to 4 sub-areas: open padlock = system disarmed, closed padlock = system
armed, house = internal arming active
5
Error symbol: indicates an alarm, reset, fault etc.
Note:
A "warning triangle" appears at the bottom of the display on the right-hand side if the alarm panel
detects a problem. The explanation (description of the problem) is not shown unless an access level 2
(user) or access level 3 (installer) code is entered.
A er a valid code has been entered the message appears in plain text (problem, fault, warning, alarm
etc.) The message is hidden again once the user has acknowledged or con rmed it. The noti cation
disappears automatically a er a one-minute time out.
6Menu symbol: used to access the user menu
1 2 3
6 5 4
13|1212
7. Menu navigation and operation | 8. Arming and disarming the system
Cursor control
The Secvest menu is mainly navigated using the cursor keys located below the display:
These keys are used to scroll through the menus and activate specic scenarios when the system is
being armed, amongst other functions. More information is provided in the next chapter, "Arming and
disarming the system".
A manual restart is initiated when the “upward” and “downward” navigation keys are simultaneously
pressed for more than ve seconds. For details, see section 16.1 Manual restart
These keys are used to select menus or symbols, change values and also exit the menus again.
Thefunction of both keys adapts dynamically to the text shown on the display. If, for example, "Menu"
is shown on the le side of the display, press the key below and enter your user code. This brings
you to the user menu which you can exit again by pressing the key.
The cleaning mode is started when the le and right navigation keys are pressed simultaneously.
Fordetails, see section 10.5.1 Functions - Cleaning mode
Note:It is not possible to use the alarm panel during cleaning; this is especially true for the double key
functionality (re, intrusion, medical emergency, care).
8.1 Arm/disarm keys
The arm/disarm keys for the alarm panel are located below the cursor eld. These keys can be used to quickly
and conveniently arm or disarm the alarm panel. Additional arming options are covered in detail below. In
the standard conguration, Secvest is armed on a time delay, meaning it is only armed aer the exit delay
programmed by your specialist installation contractor has expired.
This key is used to start "internal arming". Only the detectors for "perimeter protection" are activated,
so that you are still able to move around the building freely (even if there are motion detectors installed
indoors, for example).
7. Menu navigation and operation
8. Arming and disarming the system
1414
8. Arming and disarming the system
This key is used to quickly arm the complete system. No user code is required for this. Note that when
this key is pressed ALL detectors including those in all sub-areas (if there are any) are activated. This
function will only work if the key has been enabled in consultation with your specialist installation
contractor. This key has no function if it has not been enabled beforehand. If necessary speak to your
installation contractor if this key function is required.
This key is used to disarm the system again. A er the disarm key is pressed you must enter a valid user
code. The complete system is then disarmed (including all sub-areas).
8.2 Graphical display of arming/disarming on the display
This section contains information on how the arming or disarming of the alarm panel is shown on the
display. This assumes that your system has been con gured with just one sub-area. All detectors are therefore
assigned to sub-area1. In this case sub-area1 is the entire premises.
8.3 Arming/disarming via the quick arm keys
1. If the system is disarmed, the display responds as follows: The open padlock
symbol indicates the disarmed status of the alarm panel.
2. If the key is then pressed, the system is completely armed. As mentioned
previously, the system is armed only once the delay time has expired as
programmed by your installation contractor.
3. You should leave the premises within this time delay. The closed padlock
symbol then indicates the armed status of the alarm panel. To disarm the
alarm panel again, simply press the key and enter a valid user code. The
system is then disarmed with the audio message, "The alarm system is
disarmed" and the open padlock symbol visually indicates this status.
This method of arming the system as described here using the quick arm keys is one of the fastest and provides
a representative example of how system arming works in general. The next section provides information on
other ways to arm the system. Not all of these options may be available, as they depend on the con guration
of your system by the specialist installation contractor. If necessary speak to your installation contractor if you
desire a speci c method of arming your system.
15|1414
8. Arming and disarming the system
8.4 Arming via the user code
The system can be armed by directly entering a user code.
Thesystemhas either been con gured with a 4 or 6-digit user code
inconsultation with your specialist installation contractor.
This code should be changed during commissioning, however. If a new user is added, a separate code is
created for this user. Every user should take note of their individual codes.
1. To arm the system, simply enter a user code. Please note that the "menu"
key is not pressed before entering this code. Otherwise you will be directed
to the user menu, from which you cannot arm the system.
2. A er the code is entered the "delay time" starts (in the standard con guration
of the system). You should leave the building within this time delay. For this
reason, ensure that su cient time is planned to exit the building. If, for
example, 35s has already passed and you still have to get out the door, there
is not enough time. A false alarm may be triggered, as the opening and
closing of the door takes a bit of time in itself.
3. If the delay time has expired, the system is armed: you have now successfully
armed sub-area1 and can disarm it again by entering a user code.
If a window is still open, for example, when the alarm panel is armed, an error message is displayed.
Correct the error (close the window) and then rearm the alarm panel. If the error cannot be corrected, you
can arm the alarm panel anyway by pressing the "Lock all" key. In this case the alarm panel is armed with
"hidden zones". This means that all open detectors or detectors with faults are ignored during monitoring.
These detectors will not trigger an alarm in this case! These zones only remain hidden until the next time
the system is armed.
1
4
7
*
2
5
8
3
6
9
#
16
8. Arming and disarming the system
8.5 Arming sub-areas
In addition to the option of arming a sub-area via a user code, the system can also arm additional sub-areas.
The procedure for this is given here using the user code entry example. This function must be precon gured
by your specialist installation contractor.
A er entering the user code, you are asked to con rm which sub-area(s) you wish to arm. Alternatively you
can also arm the complete system when, for example, you plan on leaving the premises.
1. In our example the alarm panel is divided into 4 sub-areas. These are
displayed as disarmed by the open padlock symbol. First enter your user code
as usual.
2. Once the user code has been entered, the menu changes as follows:
3. Select "Change" and the display changes as shown in the  gure on the le .
Click "Done" to arm all sub-areas. The system is now completely armed.
4. If you only wish to arm certain sub-areas, click on "Change" and use the
key to navigate through the four sub-areas until the sub-area you wish to
arm is selected. Click on "Done" to arm the selected sub-area. Repeat the
same procedure to arm other sub-areas.
17|16
8. Arming and disarming the system
8.6 Individual sub-areas
1. If you wish to arm two sub-areas, proceed as follows: enter your user code.
Using the arrow keys, select the two sub-areas to be armed. The
selections are visually highlighted. Set the selected sub-areas to the
open padlock symbol via the "Change" function. Leave the sub-areas you do
not wish to arm "empty". In this case the menu looks like the example given
in the  gure on the le .
2. Click on "Done" and system sub-areas 1 & 3 are armed, while sub-areas 2 & 4
remain disarmed. A er the arming time, the Secvest display then looks like
the example given in the  gure on the le .
3. To arm only sub-area 2, repeat the steps as described above. Select the
individual sub-areas, click on "Change" and set the value for the sub-area to
"empty" as shown in the  gure. The sub-area to be armed (sub-area2 in this
case) should be set to "active" using the "Change" function. Click on "Done"
to arm just this sub-area.
8.7 Internal arming
In addition to the option of arming the complete system and sub-areas, the system also o ers the option
of "internal arming". This type of arming is preferred when occupants are home and wish to arm just the
perimeter of the premises. Certain detectors indoors (such as motion detectors) are disabled so that occupants
can move freely within the building. A practical example here is application in a private home.
The following options are available for internal arming:
Option 1:
Press the key to internally arm the system with just one touch. The quick
arm option must be enabled in advance by the specialist installation contractor.
Option 2:
Enter a user code to arm the system. Click and hold "Change" until the house
symbol appears. Click on "Done" and the system is "internally armed".
You can now move freely around the house even though motion detectors
may be installed. The perimeter of the premises is armed, so that an intruder
attempting to break in from outside triggers an alarm.
18
8. Arming and disarming the system
8.8 Internal arming via chip key
The procedure for internal arming via the chip key is virtually the same as arming the
complete system: Hold the chip key in close proximity to the ABUS logo and swipe
it over the logo briey. A prompt appears, requesting conrmation on the type of
arming required. Click on "Change" as usual and select the house symbol. Click on
"Done" to arm the system internally.
8.9 Internal arming via remote control
On the remote control, the * key is assigned the "internal arm" function as standard.
This symbol is on key2 of the remote control. Press the key and the system is internally
armed. Visual feedback is provided next to the * symbol: brief ashing (green) for
sending the signal, then ashing (red) to indicate successful internal arming.
8.10 Arming via wireless control panel
An additional way of arming the system is provided via the optional wireless control
panel. This arming/disarming option is as similar as possible to the other system
options. Only the operation method is
dierent, as the wireless control panel does
not have a display. Please read the individual operation options in the user manual for
the wireless control panel.
8.11 Arming via remote control
If there is a remote control, you can press the corresponding keys to arm/disarm the
system (all sub-areas are armed/disarmed simultaneously) and internally arm the
system if you as the user are authorised to do so. You can also check the status of
the system. The remote control provides visual system feedback for all entries ("2WAY
function"). For a detailed explanation of the individual functions of your remote
control, please read the user guide for the remote control.
19|18
8. Arming and disarming the system
8.12 Arming via chip key
The chip key can be used to completely arm and disarm the wireless alarm panel (or
a sub-area, if there are any) without touching the panel itself. The chip in principle
eliminates the need to enter a code. If you as the user to whom the chip is assigned
are authorised to arm or disarm multiple sub-areas, you must then decide which area
to arm aer you have swiped your chip key. The reader area for the chip key is located
at the height of the ABUS logo. You only have to swipe the chip in the proximity of the
reader area to arm the system – you do not have to touch the housing.
1
4
7
*
2
5
8
0
3
6
9
#
8.13 Arming via delay times
If you enter a code directly on the alarm panel (or via chip key or quick arm keys), the following "problem"
occurs: You must still be able to leave the premises through the doors. If the system were automatically
armed, you would not be able to leave the premises without triggering an alarm, if you have a magnetic
contact on the doors, for example. For this reason there is a "delay time". The delay times are precongured
by your specialist installation contractor.
There are generally two delay times:
• Exit delay
• Entry delay
The exit delay is set to 40s as standard (the time can be adjusted by the specialist installation contractor
according to your needs, however). Following the start of the exit delay, the premises must be le within
this time.
Ensure that all windows and doors etc. are closed rst before activation.
20
8. Arming and disarming the system
Important: if the exit delay has expired and you are still inside the building, your movement, for example,
will trigger an alarm if detected by a motion detector.
The entry delay gives you a sucient timeframe to disarm the system aer opening the doors when the
system is armed. The entry delay should also be programmed in consultation with your specialist installation
contractor. Ideally the entry delay should be as short as possible. If you enter your premises through the
doors, you should hear a pulsed tone. As long as this tone sounds you have time to disarm the system. Disarm
the system using your code (or chip key/disarm key).
Important: if the entry delay expires without the system being disarmed, an intruder alarm is triggered.
8.14 Preventing arming of the system
The alarm panel prevents arming in the following circumstances.
Intrusion detectors (apart from the entrance) are open. Once they have been closed the arming
procedure starts.
A panic button or panic transmitter has been triggered.
The system or a component or detector/zone is showing tampering.
If communication or signalling devices have faults, this
would prevent transmission of notications.
A supervision shutdown in a wireless component
The user can override permissible events (shutdowns).
Aer the start, a continuous tone sounds.
Make your way out of the building and open and close the doors in time.
The continuous tone is replaced by a pulsed tone when the door is opened/closed. It will then return to
acontinuous tone.
The system also allows a special type of exit delay. the system is only armed once the doors are closed.
Theexit delay is therefore exible to allow you to take whatever time you need to get out the door. Speak to
your specialist installation contractor if you desire this type of arming.
21|20
9. Responding to an alarm
First of all: remain calm. An alarm does not always mean anintrusion. Sometimes an alarm is caused by
something else, such as a self-triggered false alarm.For this reason, get a feel of the situation  rst and then
respond accordingly in a composed manner.Disarm the system, check the reason for the alarm and then reset
the alarm.
If an alarm is triggered,  rst disarm your alarm panel by entering a user code, for example. You will then be
prompted to "reset" the alarm panel. This means that you must still "acknowledge" the alarm on the system
in order for it to be ready for operation again.
The alarm is then shown on the display. "T2" means that an alarm has been triggered in sub-area2. "Intrusion
Z202 alarm" means that an intruder alarm has been triggered in "zone202" in this sub-area. This "zone02"
is the second detector in the system, with the name "MC kitchen" (magnetic contact in kitchen). You can now
go into the kitchen to see what exactly has happened near this detector.
If the cause of the alarm is clari ed and corrected, press "Reset". The system is
then reset and ready to be armed again. Note that a reset is necessary. If this is
ignored (e.g. if you press "Exit") the reset does not take place properly and
appears automatically during the next arming process. If no entry is made, the
graphical display disappears a er 1minute but remains on the system.
Important: occasionally you may  nd that an alarm cannot be reset. This may occur, for example, if the
housing of your alarm panel and its components have been opened and a tampering alarm has been
triggered. This can be corrected only by your specialist installation contractor.
9.1 Alarm types
An alarm can have various causes. The following alarms exist in principle:
• Tampering alarm
• Intruder alarm
• Panic alarm
• Technical alarm
• Fire alarm
• Emergency call or medical emergency alarm
• Entry delay exceeded
• Exit delay exceeded
The Secvest has four di erent types of alarm. Depending on the status of the system (disarmed, armed,
internally armed), the following alarms are available (depending on the setup or programming of the alarm
panel):
9. Responding to an alarm
22
9. Responding to an alarm
Internal Local External Silent
Alarm panel siren üüü–
Indoor siren üüü–
Outdoor siren üüü–
Wireless control panel üüü–
Information module üüü–
Visual alarm, such as ashing light üüüüopt.
Diallers, such as monitoring station switching,
textmessage, email, etc.
üopt. üopt. ü ü
Relay üopt. üopt. üopt. üopt.
9.2 Alarm forwarding
If the communication interface of the Secvest has been programmed (speak to your specialist installation
contractor),
the following alarm forwarding options are available (depending on the conguration of your
system and the connection used, such as IP, PSTN):
• Alarm forwarding via telephone (analogue or VoIP)
• Alarm forwarding to a monitoring station (MS)
• Alarm forwarding via email
• Alarm forwarding via text message
• Emergency call: emergency switching to medical services (e.g. Tunstall)
9.2.1 Alarm forwarding via telephone
With alarm forwarding via telephone you receive a telephone call and hear a message (recorded by you or
the specialist installation contractor), for example: "Intruder alarm at bathroom window. Please arrange
help." Proceed as follows:
1. The call occurs on the telephone and is displayed there like any other call.
2. Accept the call.
3. Listen to the entire message. The message is dierent depending on the cause of the alarm.
4. The recorded text is repeated three times. Aer the third time, the microphone on the alarm panel
is enabled and you can listen to what is happening in the room. You also have the following key
commands available (your telephone must be DTMF-compatible):
Telephone key (DTMF) Meaning
Listen 1
Speak 2
Toggle between "Listen" and "Speak" *
Playback messages 3
End call 5
End all calls 9
23|22
9. Responding to an alarm
5. If you feel capable of resolving the problem yourself, acknowledge the alarm transmission by pressing 5 or
9. 5 means that the attempt to call you is stopped. Other contact numbers on the system may be called,
however. 9 means that the attempt to make any calls is stopped. No other contacts are called.
6. If you cannot resolve the problem yourself, press 5 in any case. The alarm is forwarded to additional
people.
You can "remotely control" the alarm panel via the telephone keypad (if this function is enabled). For more
information, see "Advanced system operation".
9.2.2 Alarm forwarding to a monitoring station
If switching to a monitoring station is implemented, the monitoring station (MS) takes care of acknowledging
the alarm transmission and coordinating help. Speak to your specialist installation contractor if you have
questions about monitoring station switching.
9.2.3 Alarm forwarding via email
If the Secvest is connected to the internet (e.g. via a router), it can also forward an alarm via email. The alarm
panel text (e.g. "Intrusion Z01 alarm") is sent to a predened email address. If you are also using the Secvest
PIR camera, the alarm image can also be attached to the email. Contact your specialist installation contractor
if you wish to set up this function.
9.2.4 Alarm forwarding via text message
Similarly to email transmission, alarms can be forwarded via text message (for example using the optional
GSM module).
9.2.5 Alarm forwarding in the event of a personal or medical emergency
If your household includes a vulnerable person, you can also set up forwarding for local alarms to a monitoring
station specialised in handling medical emergencies. Speak to your specialist installation contractor about
setting up this function.
2424
10. User menu
The user menu helps you con gure certain basic functions of the system. You can create and manage users,
set the date and time and add and remove contacts.
10.1 Users
There are two di erent "levels" of the user menu. Log in as an "administrator" to delete other users, for
example. Log in as a "normal user" to use the system with limited options in certain menus – you cannot edit
or delete other users in this mode. Certain menus are not accessible for "normal users", such as "Contacts"
and "Info". The administrator is in charge of managing these menus.
The following contains an overview of the structure of the user menu and the options provided by these
menus when you are logged in as an administrator:
1. To log into the user menu, select "Menu" and enter an admin code. The  rst
menu appears.
2. As a system administrator you can manage users and create new users.
Loginto the user menu with your admin code and go to the "Users" menu.
3. To add a new user, select "Add user". You are then guided through the setup
options for a new user step by step.
4. User name: Using the Secvest keypad, enter the name of the user.
5. Select which user level the new user will have: Normal user: a normal user
has limited options compared to an administrator. Normal users cannot
create new users or edit existing users other than themselves, but they can
change their own codes and assign remote controls, for example.
Administrator: an administrator has advanced options in the user menu.
Administrators can create new users and edit existing users. There are also
more advanced options in other menus, such as in the system con guration.
Usually one administrator per household is su cient.If the premises involve
a commercial property with multiple employees, for example, it may be
agood idea to create additional administrators.
10. User menu
25|2424
10. User menu
6. The next step involves assigning arming/disarming authorisation for sub-
areas. Select "Done" if the user will be authorised for all 4 sub-areas.
Otherwise make adjustments using the "Change" function.
7. Assign an access code. This code should ideally be changed by the user
themselves and kept safe by them. Ensure that the code is "secure". Code
combinations such as "5678" are less secure than "2671", for example.
For a higher degree of security, the system can be precon gured to accept
6-digit codes. Speak to your specialist installation contractor if your system is
con gured for only 4-digit codes. A 4-digit code is created in this example.
This code must be con rmed once a er it is  rst entered. Alternatively you
can also select "No code". In this case the user can only arm the system via
chip key or remote control.
8. Additional components can be assigned to the new user. The  rst prompt is
for a chip key. Take the chip and swipe it across the ABUS logo in close
proximity to the housing. If no chip key is desired, select "No chip key".
9. A remote control can then be assigned. Press any key of the remote control.
If no remote control is desired, select "No remote control".
10. Nursing emergency call if your household includes a vulnerable person, you
can give them a mobile emergency call button. This button is used to trigger
an internal alarm quickly if the person needs help. Press the nursing
emergency call button key once to assign it.
11. Panic alarm button: you can also use the emergency call button as a panic
alarm button. Note that if the button is already being used as an emergency
call button, it cannot also be used as a panic alarm button at the same time.
12. Medical emergency call: you can also use the emergency call button/panic
alarm button as a medical emergency call button. Note that if the button
is already being used as a emergency call button or panic alarm button,
itcannot also be used as a medical emergency call button at the same time.
13. The following con rmation then appears: "New user added". You can create
additional users in the same way.
26
10. User menu
Proceed as follows via the web interface:
Log in as an "administrator", click on “Users” on the right hand side and then click on “Add user”. You can
now specify a name, type, code and sub-area.
Then login with the access details that have been set or the user details for this user and add “Chip key”,
“Remote control”, “Panic alarm”, “Medical pendant” and “Care pendant”. Follow the instructions on the
display.
10.1.1 Editing users
Here, the administrator can edit existing users.
Use the cursor keys to select the user to be edited. Then select “Edit user”.
The administrator can only change the name, type and sub-area for other users.
The administrator can select and edit their own “Name”, “Code”, “Chip key”,
“Remote control”, “Panic alarm”, “Medical pendant” and “Care pendant”.
10.1.2 Removing users
To remove users (such as an employee who has since stopped working at the
premises), select the user in question and remove them from the system.
Allcomponents assigned to this user, such as remote controls, are automatically
deleted.
10.1.3 Creating a user "threat code"
In addition to the user levels of "normal user" and "administrator" you also
have the option of creating a "threat code". This code is used to seemingly
disarm the system during a hold-up when the intruder is watching. A silent
alarm is still triggered in the background, however. For this function to be
enabled, an appropriate communication interface (e.g. telephone or monitoring
station switching) must be set up. The steps for setting up a threat code user are
the same as those for setting up any other user. Proceed as follows:
User menu -> Add user -> Name -> "Threat code user". Create a code for this
user. This code should be known to all users of the alarm panel. Then if an
intruder enters the premises and forces you to disarm the alarm panel, simply
enter this "threat code". The system appears to disarm as normal. The silent
alarm is triggered via telephone switching, however.
Important: Your specialist installation contractor must enable the function beforehand to make the "User
threat code" option appear in the user menu. If in doubt contact your specialist installation contractor
ifthis option does not appear in the menu.
27|26
10. User menu
10.2 Voice memo
This function is used to leave someone else a message ("Memo function").
Record a short reminder, for example, and then arm the system. The next person
to disarm the system is noti ed with the text "You have a message" and
acorresponding symbol. Select "Recording" to record a 30-second message and
then save it. Any user can delete this message a er it has been played back. This
function can be completely disabled in consultation with the specialist
installation contractor.
10.3 Hiding zones
It may occasionally be necessary to exclude a detector (also called a "zone")
from monitoring, for example if a detector is faulty or a zone cannot be closed
for some reason. The system then indicates the detectors that can be hidden.
The settings mean: Ü = monitored and G = locked (not monitored). Select the
detector to be hidden and press "Change". Note that detectors to be hidden
manually must  rst be con gured for this function by the specialist installation
contractor. For this reason not all of the detectors in the system may appear in
the list of detectors which can be hidden if this has been set up that way
beforehand. If detectors are hidden, they are no longer monitored when the
alarm panel is armed. A hidden detector is "unhidden" the next time the system
is disarmed and must be hidden again manually to be excluded from monitoring
the next time the system is armed, if desired.
Using the web interface, it is also possible to hide zones. This requires selecting
the “Hide zones” button, which will open a list of all the zones which can be
hidden.
28
10. User menu
10.4 Outputs on/o
If your installer has con gured the outputs as the “user de ned” type, you can switch them on and o here.
10.5 System configuration
The following settings can be de ned in the system con guration:
• On/o functions: settings for certain special functions such as door bell and
voice messages.
• Date & time: setting for the date and time
• Remote controls: reprogramming of key assignments for remote controls
• Volume settings: setting for the volumes of di erent tones and messages
• Web access: activation/deactivation of web access
• Time schedules active/inactive: Con guration of time schedules for
automatic arming/disarming
10.5.1 On/o functions
Select “Functions” to access the following options. These options will be clari ed in the subsequent sections.
Key front menu Touch front menu
Bell Bell
Voice message Voice message
Activity monitor Activity monitor
Display contrast Display contrast
Backlighting brightness Backlighting brightness
Backlighting for menu keys < hidden >
Backlighting for arm keys < hidden >
Backlighting for number keys < hidden >
Zone name announcement Zone name announcement
Restart Panel
Administrator only
S/W >=1.01.00
hidden for normal users
Restart Panel
Administrator only
S/W >=1.01.00
hidden for normal users
Keypad tones Keypad tones
< hidden > Dynamic backlighting
< hidden > Cleaning mode
29|28
10. User menu
Bell
If the "Door bell" property is congured for a detector (e.g. for a magnetic contact at the entrance of
abusiness), the disarmed alarm panel triggers a tone similar to a door bell. This function must be congured
by the specialist installation contractor. This indicates that someone has entered the business premises. If you
wish to disable this function for a certain time period, it can be disabled here.
Voice message
In this menu you can disable the audible messages on the alarm panel (e.g. "Please note the message on
the display").
Activity monitor
If the "Activity monitoring" property is congured for a detector (e.g. a motion detector in the hallway),
the function of a motion detector can be "reversed". This function must be congured by the specialist
installation contractor. If the function is reversed, an emergency call alarm is sent aer a dened time period
in which no movement has been detected. This function is used to monitor older, vulnerable members of
the household. Aer a dened time period, an emergency call is sent when the regular "presence detection"
atapreviously designated motion detector has not triggered. This allows vulnerable members of the household
who generally spend their time moving around a specic room to receive help quickly if their "presence" is
not detected aer a certain time due to a fainting spell or something similar.
Display contrast
Change the contrast of the Secvest display here.
Backlighting brightness
Change the display brightness setting. You can select "low", "medium" or "high".
LCD backlighting / backlighting
LCD backlighting
Only visible if the key front is installed. Here you can set the illumination of the display.
⋅ “O” turns the illumination o
⋅ “On” web access enabled
⋅ “When active” web access enabled
Backlighting
Only visible if the touch front is installed. Here you can set the illumination of the complete touch
front. LCD backlighting, menu keys, arm keys and number keys
30
10. User menu
⋅ “On” turns the illumination on in order to keep the complete touch front lit
constantly.
Note: LCD backlighting and all backlighting of the keys are always turned on. The wakeup function is
deactivated.In case of a power failure, the illumination switches to “When active” in order not to use
unnecessary electricity from the battery.
⋅ “When active” means that the illumination of the complete touch front only remains on for
approx. 30 s aer each use. Aer 30 s it automatically turns o.
Note: Wakeup function is activated. The illumination is rst turned on when a button is pressed (rst
touch). No other action results from a “rst touch”. From the second touch on, the keypad functions as
normal. The user can then touch one of the visible symbols (house/padlocks). At the first touch, the alarm
panel will not perform the functions associated with these buttons.At rst, only the illumination is turned
on.
Backlighting for menu keys/backlighting for arm keys/backlighting for number keys
Only visible if the key front is installed. The same setup as for "LCD backlighting" applies here for the
backlighting of the menu keys, arm/disarm keys and number keys. Set the desired lighting of the keys
formenu navigation here.
Note:If the touch front is installed, these 3 menus are hidden.
Zone name announcement
Your detectors can be equipped with an additional audio message if desired. In consultation with your
specialist installation contractor, the detectors are usually already given a name, for example "MC living
room" for "magnetic contact in living room". This text can be recorded and saved here individually for each
detector, with approx. 2s allocated for each detector. If detector "MC living room" triggers an alarm, for
example, the text not only appears on the display when the alarm is disarmed, but the name of the alarm
is also audibly played back. Do not forget to select "Playback" aer recording the detector text to check what
was recorded and ensure it is correct and intelligible.
Voice message: 2 second announcement for each zone
If this function is activated:User menu -> Conguration -> Functions -> Zone name announcement ->
Enabled on and zone names are spoken, an additional announcement is made:
For an open zone
“The alarm system cannot be armed” + “<Zone name>”
For several open zones, the zone with the lowest zone number will be announced in addition.
31|30
10. User menu
During an alarm
⋅ Voice dialler Following an “individual message” and “Message x”, the zone rst triggered
will be announced in addition.
⋅ Alarm panel The zone rst triggered will be announced with each sub-area. Thesub-area
with the lowest number will be rst.
Example:
Alarms were triggered in the following zones in the following order:
Zone 226 Sub-area 3
Zone 225 Sub-area 1
Zone 203 Sub-area 1
The following can be heard over the system:
“The sub-area is deactivated! Attention! An alarm was triggered!
<Zone 225 voice message>, <Zone 226 voice message> Reset required“
Restart Panel
You can use this to restart the alarm panel manually.
This is helpful for some problems, to reset the alarm panel to a dened initial state. All the settings and
congurations are retained.
Note: This menu item is only visible to the administrator, i.e. the administrator must be logged into the
system.
A restart is only possible when
• all partitions are "disarmed" and
• the alarm panel has completed all important communications, transmissions and actions.
Select "Restart alarm panel" by pressing the "Change" menu key.
You are prompted for conrmation.
Press the "Yes" menu key.
At this point you can still cancel the restart.
Press "Back".
There are more details in Section 16.1, Manual restart (switching o and switching back on).
Keypad tones
When “On” is selected, a clicking sound via the loudspeaker is generated by pressing or touching each key.
32
10. User menu
Dynamic backlighting
Only visible if the touch front is installed.
The brightness regulation is an option for dynamic light control.
If the “Dynamic backlighting” menu item is set to “O”, it will behave similarly to the Secvest with a key front
with a xed “high”, “medium” or “low” value.
If the “Dynamic backlighting” menu item is set to “On”, the backlighting will adjust proportionally to the
ambient light.
The high, medium and low settings still have an inuence on the level and degree of the increase.
Theminimum and maximum values are:
Backlighting brightness Minimum values Maximum values
High 15% 100%
Medium 10% 50%
Low 2% 11%
Cleaning mode
Only visible if the touch front is installed.
“O” deactivates the cleaning mode.
“On” enables the cleaning mode.
The cleaning mode (factory default “On”) is started when the le and right navigation keys are pressed.
Thekeys are disabled for a total of 35 s. You can now clean the front without accidentally triggering an action.
The display shows “Cleaning mode”. An acoustic warning signal and notication on the display during the
last 5 s signalise that the keys will shortly function as normal. The display will show: “End of cleaning mode”
Note:It is not possible to use the alarm panel when it is in cleaning mode; this is especially true for the
double key functionality (re, intrusion, medical emergency, care).
Cleaning mode will stop if an alarm occurs.
If an alarm occurs during cleaning mode, the cleaning mode will immediately be aborted and the keypad
will return to normal use at once.
If a nursing emergency call timer starts, the cleaning mode will be aborted.
A 30 s “abort time” begins when the nursing emergency call alarm is pressed.
If an inactivity warning timer starts, the cleaning mode will be aborted.
A 2 minute “abort time” begins when the care activity monitor establishes inactivity.
It is not possible to start the cleaning mode when an alarm is present.
33|32
10. User menu
10.5.2 Date & time
Only visible to the administrator.
Set the time and date here. Both can be entered directly using the number keys. Click on "Next" to navigate
through the menu. Then de ne whether the system automatically adjusts for daylight saving time or whether
you wish to adjust the system manually yourself. We recommend setting it to adjust "Automatically".
Activating the check box on the web interface allows the times to be called up from an NTP time server.
Here,you can also set when the system should synchronise with the selected provider.
34
10. User menu
User menu -> Conguration -> Date & time
SNTP Time sync.
SNTP active
O
On
Sync on start-up
O
On
Sync daily
O
On
Manual sync
(synchronises date/time immediately)
NTP server name
ntp.exnet.com*
Name:
ntp.exnet.com
pool.ntp.org*
Name:
pool.ntp.org
<empty>
<empty>
<empty>
(A list of 5 congurable
NTP-server names in order of priority.)
Manual mode
Set date
Set time
Summer/winter
Automatic
Manual
10.5.3 Edit outputs
Only visible to the administrator.
If your installer has congured the outputs as the “user dened” type and has enabled editing, you can edit
them here.
You can change the following:
• Name of the output
• Polarity
• Continuous or pulse switching
• Schedule
• Event
- Up to 3 events can be assigned and edited.
35|34
10. User menu
10.5.4 Remote controls
Only visible to the administrator.
Assigned remote controls can be edited or removed here. The following options are available:
• Edit: press the * key of the remote control to reprogram it. The standard setting of the key is "Internal
arming". If you wish to switch a relay output with this key instead, however, this function can be
assigned to this key. A suitable relay output must  rst exist in the system. Speak to your specialist
installation contractor if you require this function, such as to open the garage door via a relay output.
• Remove: remove a remote control that has been lost or is no longer needed. If you still have the
remote control, press any key. If you have lost the remote control, press "No remote control" to delete
itwithouthaving to press a key.
• Delete All you can delete all remote controls in the system at once here.
• Panic response: if the remote control has a panic alarm, this function can be disabled here. The "panic
alarm" on the remote control can be triggered by pressing both padlock keys at the same time.
10.5.5 Volume settings
Only visible to the administrator.
Set the volume of di erent tones here. The tones can be changed by directly
entering a number from 0–9, where 0 means muted and 9 represents
maximum volume.
Operation tones: refers to all tones that occur when the system is being operated
such as the feedback tones when operating the system via the keypad.
Info tones: refers to all info tones, such as feedback tones for error messages.
Alarm tones: The volume of the alarm tones (intrusion,  re, etc.) can be changed
here. The volume of the messages can be changed by clicking "Select" and then
adjusting the volume using the +/- keys.
We recommend leaving alarm tones set to "9". If you set the volume of the alarm tones too low, you may
not hear an alarm in time or at all.
10.5.6 Web access
Only visible to the administrator.
De ne whether your system can be operated remotely (see "Web access") or not here:
• Disabled web access disabled
• Enabled web access enabled
36
Safety information
10.5.7 Remote updates
Only visible to the administrator.
De ne whether your system can be remotely updated here. For details, see the installation manual,
“B/Wupgrade” appendix
“Disabled” A level-4 user cannot update your alarm panel.
“Enabled” Approval is granted so a level-4 user can update your system.
10.5.8 Time schedule active/inactive
Only visible to the administrator.
You can enable the "week planner" in this menu. For example, if on Monday to Friday you want the system
to disarm at 7a.m. and then arm at 6p.m. (a typical timeframe for a shop), you can set this up here.
We recommend setting up the week planner via the web interface (see "Web access"). "Web access –
Timescheduler" describes the setup of the week planner in detail.
10.6 Contacts
Only visible to the administrator.
You can manage your contacts in this menu. Use the telephone/IP interface or
similar of your Secvest, for example, to forward alarms. The contacts can be
adjusted here or new data entered. Not all  elds must be completed.
Select "Contacts" to access the following menu:
You can choose up to 12 contacts. Usually the contacts are initially set up in
consultation with your specialist installation contractor. Using the example of
"Contact A", the following options can be seen:
• Name: Enter the name of the contact
• Partitions The recipient can be assigned to sub-areas. This stipulates that the recipient will
only receive a message when an event occurs in the speci ed sub-area.
• Tel.Nr.1: Enter telephone number 1 of the contact
• Tel.Nr.2: Enter telephone number 2 of the contact here
• Email: Enter the email address of the contact
• IP address: This is the IP address of the monitoring station. Do not change this entry.
• SIP user ID: If VoIP is used, the "User ID" is entered here.
10. User menu
37|36
Important: only make changes to contact entries, such as when a number has changed or the contact
can no longer be reached. The assignment of sub-areas is only applicable to voice diallers, text messages
and email, and not to ARC/ESCC connection.
Events not directly relating to a single sub-area (e.g. the double-key function on the alarm panel for re,
intrusion, medical emergency and care alarms) will be assigned to sub-area 1.
Intrusion (remote control), intrusion (pendant), medical emergency (pendant) and care alarm (pendant).
Events triggered by these user-controlled components are transmitted to the recipient where the selected
sub-area matches the sub-area authorisation for that user
wireless control panel, double-key function for re, intrusion, medical emergency and care alarms.Events
triggered by these components are transmitted to the recipient where the selected sub-area matches the
assignment of sub-areas for that control device.
10. User menu
38
Safety information
10.7 Test
Only visible to the administrator.
The test menu provides the option of testing the various functions of your system to ensure they are working
properly. Depending on the setup level of your alarm panel, certain functions may not be available.
Select "Test" to access the following menu:
The following options are available:
• Walk test
• Sirens & Sounders
• Door locks
• Outputs
• Prox Tag
• Remote controls
• Emergency buttons
• Telephone call
10.7.1 Walk test
1
. You can test your detectors in the "walk test”. For example, if you want to know
whether a certain detector is functioning properly, you do not have to trigger an
alarm.Simply select "Walk test" and test your detector.We recommend proceeding
as follows:Open the walk test and activate the "Bell – on" menu.
2. A feedback tone sounds in this case when you trigger a detector during the
walk test.
3.
Select "System" and your detectors should be listed (the number of detectors varies
depending on the setup level of the system – in this example you see 4).
4. Then open the window with the  rst detector (such as a magnetic contact).
For a motion detector you should move around brie y within its detection
range. Repeat this for all detectors (you may have to do di erent things to
trigger them depending on the type of detector). A er a successful test the
menu should look like the example shown on the le . In this case "A" stands
for a "virtual alarm" that was triggered. The detector is working properly.
Ifthere is no entry "A" for a detector and you have tested all detectors, repeat
the test for the detector in question again. If the entry fails again, contact
your specialist installation contractor.
10. User menu
39|38
Important: ensure that you do not open the housing of a detector. Otherwise the system automatically
exits the walk test and triggers a tampering alarm. Detector housings are only opened by the specialist
installation contractor for maintenance purposes.
Under "Sub-areas" you can select whether only detectors from a certain sub-area are tested. Under "Zones"
you can select whether only certain detectors are tested. The procedure is then the same as for the walk test.
10.7.2 Sirens & sounders
Test the function of dierent sirens and sounders here. Click on "Change" to test the following:
• Internal sirens: Test the installed sirens of the alarm panel and any indoor sirens here.
• External wireless sirens: If at least one wireless siren exists in the system, it can be tested here.
Werecommend only briey testing this function. Warn your neighbours
beforetesting if necessary.
• Sounder Module If a universal module (UVM) is installed as a "siren module", you can test
itsfunction here. Again: please warn your neighbours before testing.
• Loudspeaker: Test the installed loudspeaker of the Secvest here. Select "Play/Stop"
tohearallexisting messages in the system one aer the other.
10.7.3 Door locks
If a Secvest key and/or additional door lock is installed, it is a good idea to check its function occasionally.
Engage the lock while the alarm panel is disarmed – the message "Open" or "Closed" is displayed.
10.7.4 Outputs
If a relay output is enabled this menu appears here. Click on "Select" and test the output using the "On/o"
function. If relay contacts (from the Secvest, universal module or wireless socket) have been enabled by the
specialist installation contractor, you can test these if necessary. The corresponding relay contact must be
enabled for you as the user in order to test it. There are relay contacts that only activate when an intruder
alarm is triggered and therefore cannot be accessed in this menu. Speak to your specialist installation
contractor if you wish to access a relay contact, for example to use a wireless socket for lighting control.
10.7.5 Proximity / chip key
If your system has a proximity chip key and you wish to test its function, take the key and swipe it over the
chip key reader area in the lower area of the alarm system (at the height of the ABUS logo). If the chip key is
read successfully, the display indicates which user the chip key is assigned to.
10. User menu
40
Safety information
10.7.6 Remote controls
If you wish to test the function of a remote control, select this menu and press the di erent keys one a er
the other. The display then indicates which keys have been pressed and what function is assigned to the key
in question. The standard assignment of the remote control is:
Closed padlock Complete arming
Star key Internal arming (= perimeter protection on)
? key Status query
Open padlock Complete disarming
The user assignment is also displayed and the signal level of the triggered remote control, e.g. RSSI:9.
RSSIstands for "received signal strength indication". An RSSI value of "9" indicates an excellent received
signal strength, as the scale for the Secvest runs from 1–9, where 9 is the maximum strength.
10.7.7 Emergency call button
An existing emergency call button (for nursing, panic alarm or medical emergency) can be tested here by
pressing the emergency call button. Depending on which function has been assigned to the emergency call
button, the function of the button is displayed. For example, "PFN alarm" (PFN = nursing emergency call).
Aswith the remote control, the RSSI and user assignment are also displayed.
10.7.8 Telephone call
If your system is equipped with an active telephone interface (PSTN or GSM), you can test the function of the
connection by making a test call. Enter any telephone number. If dialling is successful you get a dial tone.
However, when the other party answers, you can only hear the other party.
If the connection is not activated or is otherwise disrupted, you get the error message "Communication
error". Check the other telephone connections in the house if there are any and contact your specialist
installation contractor if necessary.
Note: You can also recharge the credit for your prepaid GSM SIM card via the GSM telephone connection.
Dial the corresponding service telephone number, follow the instructions and enter your recharge code
using the number keys. The service portal sometimes requires you to use the star key (*) or the hash key
(#) for navigation.These keys can also be used here.
10.8 Log book
You can view the "log book" in this menu. The log book contains all of the
relevant data for the alarm panel including the date and time. The memory can
hold up to 600 entries. If the memory is full, the oldest entry is deleted and
overwritten with the new entry (FIFO principle:  rst in  rst out). A list of the
di erent log book entries can be found in the appendix under "Log book
overview".
10. User menu
41|40
10.9 Info
Only visible to the administrator.
This menu is used to check the so ware version of the wireless alarm panel and
query the communication interfaces. You cannot change any con gurations in
this menu.
10.9.1 Alarm panel
• Version: so ware version, e.g. V2.01.08
• S/N: serial number of the alarm panel, e.g. FUAA50000#E……
• Part No.: article number of the alarm panel, e.g. FUAA50000
• Language: set language including language version, e.g. English V1.24
RF Device exclusivity: Indicate which components can be added.
“Yes” only “new” components, e.g. FUMK500XX, FUBW50000
“No” all components, also “old” components, e.g. FU8320, FU8350
The web interface provides the following information:
10. User menu
42
Safety information
Name/function Explanation
Version, language Version number of the so ware currently installed on the alarm system
Version number for the con gured language
Serial Number Serial number of the alarm system
Part No.: Article number of the alarm system
Alarm panel time, date Currently set time and date on the control panel
Date & time Synchronises date and time of the alarm panel with the date and time from
the PC via mouse click
Zones Overview of available and con gured zones
Wireless control panel Number of components in use
Wireless sirens Number of components in use
WAM Number of components in use
Door locks Number of components in use
Partitions Number of sub-areas in use
Outputs Overview of available and con gured outputs
Housing front tampering Speci es whether the tamper contact on the front of the housing has been
triggered
Bell tampering Speci es whether the tamper contact on the wired, connected siren has been
triggered
RF Jamming Speci es whether the alarm panel has detected RF jamming
Alarm panel A/C fault Displays whether the alarm panel is connected to 230V or if a fault is present
External DC fault Displays whether the alarm panel is connected to 13.8V external DC power
supply or if a fault is present.
Ext. DC voltage in Speci es the voltage of the external DC power supply
Battery status Status of each battery (with voltage if required)
Auxiliary Output voltage to the power supply output terminal
10.9.2 Communication
PSTN: Info => Communication => PSTN
PSTN link status query. The Secvest then checks the installed landline. If it is
not enabled or is disrupted, the error message "Error" appears. Otherwise the
message "Test successful" appears.
GSM: Info => Communication => GSM
(This menu only appears when the GSM module is installed.) You can query information about the GSM
module here, such as IMEI, SIM card number (if supported by the provider) and
network operator. Select "Network", for example, and the network operator
and signal level are displayed.
(This menu only appears when the GSM module is installed.) You can query information about the GSM
(This menu only appears when the GSM module is installed.) You can query information about the GSM
(This menu only appears when the GSM module is installed.) You can query information about the GSM
10. User menu
43|42
The signal level in this case ranges from 1 (very poor reception) to 10 (excellent
reception).
Ethernet Info => Communication => Ethernet
If the system is integrated in a network via a network cable (e.g. via the router in the home network),
youcanview the items listed below. Speak to your specialist installation contractor if in doubt, as for some
of the listed values speci c knowledge of networking is required.
IP address
If the Secvest is located on a network the IP address is shown here, e.g. 192.168.178.23. If (DCHP) is shown a er
this in brackets, the Secvest automatically obtains its IP address from a DHCP server, for example, in a router.
If the Secvest is not networked, "0.0.0.0" is displayed here.
IP Subnet Mask
The subnet mask is displayed here. In a private network this is normally 255.255.255.0.
Gateway IP address
If the Secvest is located on a network the IP address of the gateway is shown here. An example of a gateway
in a private network is the router, e.g. the Fritz!Box.
DNS primary IP address
This is the IP address of the Domain Name System (DNS).
MAC address
The hardware address of the network adapter for the Secvest is given here. A MAC address is globally
unique.
IP Link Status
The message "OK" appears if the Secvest has a functioning network connection. "Error" appears if the network
connection is disrupted or the Secvest is not connected to the network at all.
10. User menu
44
11. Advanced system operation
11.1 Remote control
If you have a remote control you can arm or disarm the wireless alarm system by pressing
the remote control keys:
Key 1 Arm
Key 2 Arm internally (or ‘Switch output’. The key has to be
reprogrammed for this function).
Key 3 Status query
Key 4 Disarm
11.2 Wireless cylinder lock ("Secvest key") Arming
The wireless cylinder lock can be used to easily arm the system. To arm the alarm panel, rst press the button
on the cylinder and then lock the doors. Once the doors are locked the alarm panel is armed.
Disarm
Likewise, you can completely disarm the system by opening the doors. Open the doors as normal. The wireless
cylinder lock transmits the signal to disarm the alarm panel, which disarms the system immediately.
11.3 Additional door lock (FU7010/7025E)
If a wireless additional door lock from ABUS is installed, you can arm and disarm the
system in a way similar to the wireless cylinder lock. The additional door lock provides
a high degree of electromechanical security as it ensures intruders are met with up to
one tonne of pressure resistance and also triggers an alarm if there is an attempt to
force the door open with a lever.
For more detailed information on this product’s operation, see the relevant instruction manual. Thepractical
steps are described here briey.
Arm
To arm the alarm panel, lock the doors from outside using the key. Aer 2 complete revolutions from outside the
system is automatically armed. Depending on the article number of the product, the system can also be armed
from inside: for FU7010 (with rotary knob) you need one revolution, for FU7025 you need two. Important: if you
wish to leave your premises very briey but still want to lock the additional door lock, you must press the key for
"suppressing arming". The door look must then be activated within 30s so that the system remains disarmed.
11. Advanced system operation
45|44
11. Advanced system operation
Disarm
To disarm the alarm panel unlock the additional door lock accordingly. Unlocking the lock automatically
disarms the alarm panel.
11.4 Operation via telephone
If the alarm panel is connected via the A/B interface, the wireless alarm panel can call you to
report an alarm. Once you have listened to the message, you can send commands to the system
by pressing the keys on your telephone keypad. The system sends information about the status
of your commands by playing back the voice messages (e.g. "Reset required"). You can also call
your wireless alarm panel if no alarm call has taken place, in order to check your alarm system:
1. Select the alarm system telephone number. You will then hear three beeps in succession.
2. Enter the access code via the telephone keypad. You will then hear two beeps in succession.
You can then use all of the following commands upon consultation with your specialist installation contractor.
The specialist installation contractor may still need to enable these commands before they can be used:
Role Key combination
Listen 1
Speak 2
Toggle between "Listen" and "Speak" *
Playback messages 3
End call 5
End all calls 9
Disarm system #0*0
Arm system #0*1
Internally arm system #0*2
Stop sirens #1*0
Reset system #1*1
Query system #3*
Switch output nnn to "On" #9*nnn1
Switch output nnn to "O" #9*nnn0
Toggle output nnn #9*nnn*
If you are called by the alarm panel in the event of an alarm, you do not need to enter the access code.
However, you can operate the system using key combinations 1, 2, 3, 5 and 9. Key combinations #0*0 etc.
must rst be enabled by your specialist installation contractor before they can be used.
46
12. Operation via web (app/browser)
The Secvest can be easily and conveniently operated via the internet or a local network using the integrated
network interface. To use these functions, the Secvest must be integrated in a network and congured
accordingly by your specialist installation contractor. If you have any questions, please contact your specialist
installation contractor. The following describes which options are available for operating the system via the
network and how these options function.
In principle you should have these options for operating the system:
12.1 Operation via web browser
If you can access your home network from a computer, smartphone or tablet and the Secvest is also located
on this network, you can access the web interface of the Secvest by entering the IP address of the Secvest in
your browser (e.g. Firefox). The web interface can be used to operate the Secvest for arming and disarming
the system with all the control options available directly on the alarm panel (see "Basic operation"). You can
also switch to the user menu level and dene settings via the web interface. You have virtually the same
options as on the system itself in this case.
12.2 Operation via app
The second option for operating the Secvest via the network
is to access it via the Secvest IP app. You can purchase the
app in the iTunes or Google Play Store (account required). Once
installed and set up on a smartphone or tablet, you can do the
following things with the app:
• Arming, disarming
• Internally arm/disarm the system
• Arm/disarm sub-areas
• Switch outputs
• Submit status queries
• ...
As with operation via web browser, access to the system via
network must be set up beforehand.
The following pages provide a detailed description of the
procedure for both options.
12. Operation via web (app/browser)
47|46
13. Operation via web browser
In addition to operation via the app, the system can also be operated via a web browser. You only need
anormal web browser, such as Firefox. This section discusses how to operate the system via the web browser.
13.1 Setting the Secvest IP address
1. First you must know the IP address of your Secvest. This can most easily befound
in the Secvest user menu under "Info": select "Communication" -> "Ethernet".
2. In this case the IP address has been assigned manually as 192.168.178.4.
If(DHCP) were to appear a er the address in brackets, this would mean that
the address was automatically obtained (e.g. assigned by a router).
3. Enter this address in the address line of your web browser (without "www" or
"http"). Firefox is the web browser used in this example. Depending on the
browser you use, the display may look di erent. All standard browsers are
supported, e.g. Internet Explorer. Firefox, Safari, Chrome and Opera.
4. Usually there is a message indicating that the connection is "untrusted".
Thisdoes not mean that the connection between the PC and Secvest is not
secure.
5.
Click on "I Understand the Risks" and then "Add Exception". Then click on
"Con rm Security Exception".
6. You are then directed to the login area of the web interface.
7. Enter your user name and password. In our example, this is "1234"/"1234".
Thenclick on "Login".
13. Operation via web browser
48
13. Operation via web browser
8. You are then directed to the main menu of the Secvest. The next page provides
an initial overview of the di erent options available to you at this level.
Important!
Automatic log out function:
Based on the Secvest’s automatic log out function, this is now also possible on the web interface and Secvest
app.
• Normal user or administrator is logged in. The automatic log out occurs a er 1minute of inactivity.
• iOS/Android app: Once opened, the app closes a er 4:15minutes have passed without an input
(if“Remember PIN” is set to no) in accordance with the VdS 3169 standard.
13.2 Overview of the web interface
The web interface is very similar in its functional scope to the user menu. The control panels and menus are
rearranged, however, in order to provide a more user-friendly display on the web interface. If you are familiar
with the functional scope of the Secvest, the options of the web interface are described here brie y below:
1Overview of status of 4 sub-areas:
open padlock = disarmed | closed padlock = armed | house symbol = internally armed
2Keypad for arming/disarming/internal arming
3Menus for con guration, creating users, etc.
4Overview of status within the speci c sub-area. Are there errors/open zones?
1
2
3
4
49|48
13. Operation via web browser
13.3 Arming & disarming
The following button can be used to arm and disarm the system. The symbols have the following meanings:
1 2
3
These commands can be implemented
individually for each sub-area. First
click on the sub-area in question and
then on the corresponding arm/disarm
key:
If there is an error in the system, the
information on this is displayed as
follows (in this example a magnetic
contact is open):
If you click on "Arm" or "Internally arm"
in this case, you will  nd that it is not
possible – the padlock button remains
"open". You must  rst resolve the error
and then arm the system. If you have
successfully armed the system via the
web interface, the display looks like the
example shown here in the following
(a sub-area has been armed in our
example).
If an alarm has been triggered within the
armed sub-area, the display looks like the
example in the  gure on the le .
1Internally arm system
2Disarm system
3Arm system
50
13. Operation via web browser
Acknowledge an alarm by selecting the
red sub-area and con rming the prompt
for whether the alarm should be
acknowledged.
To reset the alarm panel, select the !
symbol that appears a er acknow-
ledgement in the triggered sub-area.
This action must also be con rmed via
aprompt from the alarm panel.
Obviously you can also "internally arm"
your system in the usual way. Simply
click the corresponding symbol (house
with padlock inside).
13.3.1 Hiding zones
Using the web interface, it is also possible to hide zones. This simply requires selecting the “Hide zones”
button, which will open a list of all the zones which can be hidden.
51|50
13. Operation via web browser
13.4 Additional web interface options
The following shows the additional options provided by web access: Many functions are explained in
the "Secvest", "Basic operation" and "User menu" sections, so this section focuses on providing a brief
explanation of the individual menu items. Only the "Time schedules active/inactive" menu item is described
in more detail in this section. ABUS recommends con guring the time schedules via the web interface if
possible, simply because it is easier and clearer to do so this way. More information can be found in the next
section, "Configuring Secvest time schedules".
The same settings can be de ned here
as on the alarm panel itself under
"System con guration".
Click on "Contacts". Use this to edit
your contacts for connections via
telephone, VoIP, email etc. Please
note, you should only make changes
in certain circumstances, such as
when one of the contacts has a new
telephone number.
52
13. Operation via web browser
Then switch to "User". Just like in the
user menu you can create new users
here and manage and remove existing
users. Click on "Add user", for example,
and follow the instructions.
Important: for S/W<2.00.00, remote
controls, chip keys, etc. cannot be
added via the web interface. This
must be carried out directly on the
alarm panel!
Switch to the "Log book". You can view
a graphical overview of the events
in the log book. An overview of the
di erent log book entries can be found
in the appendix under
53|52
13. Operation via web browser
If a "PIR camera" has been integrated
in your system, there is one point of
note here: in the web interface
a special entry is created in the log
book if the camera has triggered an
alarm. To view these entries, proceed
as follows:
Click on the camera symbol to access an
overview of the recorded images.
Then click on the individual images.
You can save these images to your hard
disk by clicking "Save" in order to use
them as evidence of a break-in, for
example.
Under "Keypad" you will  nd the
"Virtual control panel" function. You
can use this function to view the
Secvest menu via the web interface
and assign a created user to a remote
control, for example. Move the virtual
cursor keys using the mouse and go to
the "User" menu. Further options are
displayed there.
5454
13. Operation via web browser
To de ne "Time schedules" for the
Secvest, con guration via the web
interface is strongly recommended.
13.5 Configuring Secvest "time schedules"
Basic procedure: Your alarm panel’s time schedule function is especially useful in places which have recurring
routines, for example, a doctor’s surgery with regular opening and closing times. A time schedule is used to
automatically arm or disarm the Secvest.
Important: setting up time schedules in private households is generally not necessary and very di cult
to implement. Schedules are usually di cult to plan as they vary so much from day to day. Consider the
fact, for example, that an open window or similar situation is very problematic with an automated arming
setup.
Arming events
Ten minutes before the programmed event, the alarm panel starts giving an audible warning that the system
is about to be armed via a week planner event ("week planner arming"). The alarm panel also activates all
"automatic arming warning" outputs.
At the end of the warning time for week planner arming, the alarm panel stops the warning tone and
immediately arms the relevant partition(s), deactivates the "automatic arming warning" outputs and
activates all "armed" outputs. The system logs week planner arming events as "automatic system arming"
events along with the relevant partition numbers.
Timed Set
During the warning time for week planner arming, a user can delay the arming process.To do this, you need
to enter your access code in the alarm panel or hold your proximity keyfob up to the alarm panel and select
"Delay".Please note, the user must have authorisation for the partition which is to be armed.
If the timer has been delayed by a user the alarm panel stops the timer and delays all subsequent arming
events for 30 minutes. A er 20 minutes the alarm panel starts the ten-minute count down again.
Users can delay a week planner arming event in this way up to three times in total. A er the third delay,
thealarm panel is armed. Please note, this delay to the arming process has no e ect on disarming events.
5454 55|
13. Operation via web browser
If there is an arming fault
If there is an error which would normally prevent the system from being armed then the system is not armed
via week planner events either.
Ten minutes before a week planner arming event is due the alarm panel starts the warning tone for week
planner arming as usual, but when the event is due the alarm panel is not armed. The alarm panel logs an
"arming fault" and activates "arming fault" outputs.
Please note, zones with the "force arming hidden" attribute are hidden if they are open when automatic
arming is due.
Disarming events
When the alarm panel reaches the time for a disarming event, it disarms all relevant partitions.
There are no speci c warnings for disarming partitions via week planner events.
Manual arming/disarming and week planner events.
If a user arms a partition which is to be armed later via a week planner event the partition remains armed.
Similarly, if a user disarms a partition which is to be disarmed later via a week planner event the partition
remains disarmed.
Manual arming and disarming have no e ect on the times in the week planner.
If you require at least one scheduled switch, go to "System con guration" and select "Time schedules active/
inactive". This opens a new window:
The following uses an example to show
how to set up a time schedule. In the
example, the alarm panel should
disarm at 7a.m. every day and arm at
7p.m.
56
Carry out the following steps:
1For a time schedule to be active, it must  rst be "Enabled".
2
De ne when the time schedule should be active. The following options are available: Monday/Tuesday/
Wednesday/Thursday/Friday/Saturday/Sunday/Monday – Friday/Saturday to Sunday/Daily/
Exceptions. In this
example we are choosing "Daily".
3You can also lock individual time schedules if one is no longer required but you wish to retain the data
for future use. If you wish to add the time schedule, click on "Enabled".
4If you wish to de ne exceptions (such as holidays), adjust your time schedule accordingly. Moreinformation
on con guring exceptions is provided on the next page.
5
If you wish to use the time schedule for all 4 sub-areas, enable this  eld. For individual sub-areas
use the
eld 10
6
The alarm panel can warn you before it automatically arms. Choose "Acoustic" to receive an acoustic
warning signal before the alarm panel arms. Choose "Silent" for the alarm panel to arm without
providing an acoustic warning signal beforehand.
7De ne what should happen: Arm/Disarm/Internal/“No”. In this example we are choosing "Disarm".
Thismeans that nothing happens.
8Set the "Warning time" (in minutes).
9De ne the time at which the time schedule is active.
10 If you wish to arm individual sub-areas, click on the sub-areas in question here.
11
The  rst "dataset" (time schedule) is created and can be saved by clicking "Transmit". More information on
datasets is provided on the next page.
8 7 6 11
54321
10
9
13. Operation via web browser
57|56
13.6 Datasets
For each arming scheme (e.g. "Monday", "Daily", etc.) you can choose any number of 16 "datasets". Youcan
therefore con gure 16 di erent actions. For example, you could con gure your system so that it disarms
in the morning, arms at midday, disarms a er lunch and then arms again in the evening. This requires
4individual datasets.
Important: be very careful and methodical when creating datasets. Ideally you should come up with
an exact scheme beforehand and outline it in a simple table, for example. This would provide a better
overview.
13.7 Exceptions
There are a total of 20 "exceptions"
available. These are used to set up
holidays and special events, such as
Christmas or Easter. Here is an example
of how to set up an exception. You
want to set the time schedule to "Daily"
but add an exception for 24December
so that the alarm panel remains armed
and does not disarm at 7 a.m. Proceed
as follows:
1. First click on "Week planner" and then on "Exceptions". This opens a new window where you can de ne
the individual exceptions.
2. Click on "Exception 1" and enter the data for the exception. There are 20 exceptions available. You can add
these exceptions in the previous window under "Exceptions" and then link them to the dataset.
3. Add all of the desired exceptions to the calendar and link them to the time schedules as shown in the
previous section.
13. Operation via web browser
5858
14. Terms and denitions
Active intrusion protection
Even an attempt to break in is reported. This can be done using alarm components that not only combine
wireless technology with mechanical intrusion protection (mechatronic detectors), but also monitor attempts
to open a door or window using a lever via magnetic eld sensors.
Alarm panel
The switching instance of the entire alarm system, which processes all information, forwards it and responds
as necessary.
Alarm system
Common term for a burglar alarm system or danger alarm system.
Alarm type
Alarm systems may have the following alarm types: internal, local, external or silent.
Alarm zone
A detector (wireless) or detector group (wired) is monitored via each zone and can be programmed separately.
Arm components
Devices that can be used to arm/disarm the alarm panel (e.g. remote control, key switch, control panel).
Arming, disarming
“Activation” of the alarm panel – the panel triggers an alarm if an intrusion is detected (e.g. door opener).
“Deactivation” of the alarm panel – the panel does not trigger an alarm if an intrusion occurs.
Arming, disarming
Activating/deactivating the alarm panel.
AWAG (telephone dialler)
Automatic dialling and messaging device: Sounder for transmitting voice messages.
AWUG (telephone dialler)
Automatic dialling and transmission device. Sounder for transmitting digital logs (for emergency monitoring
stations).
14. Terms and definitions
5858 59|
14. Terms and denitions
Bidirectional 2-way wireless (2WAY)
Bidirectional: Bidirectional components can also receive feedback from the alarm panel and evaluate it
(e.g.via LED displays).
Certifications
Inspection seal from an independent body that ensures the high quality and safety of alarm systems (in
Germany the following are relevant: certication as per POS in accordance with accident prevention regulations
and VdS loss prevention)
Chip key/proximity
Electronic “key” for quick access without code entry.
Coding of wireless signals
Coding ensures secure transmission of signals without manipulation or tampering between the alarm panel
and its components.
Combination signalling device
Combined sounder, e.g. siren (acoustic signal) + strobe (visual signal).
Communication options
This allows for a silent alarm, via voice/test messages or digital logs, mobile wireless technology (GSM module).
Danger alarm system
Alarm system that triggers an alarm for additional dangers/emergencies as well as intrusion.
Danger detector
Device that sends a message to the alarm panel when a certain event occurs (e.g. movement, glass breakage,
vibrations).
Display
Display eld on the alarm panel for operating and conguring the panel.
External alarm (alarm type)
Alarm that causes all sounders to respond (indoors and outdoors). The event is also reported to a monitoring
station, for example.
6060
14. Terms and denitions
Flood detector
For detecting water damage and ooding, existing of a basic device and water sensor. The sensor is always
mounted at a point where ooding would rst start to occur in order to incur water damage.
Glass breakage detectors
These detectors respond to breaking glass. There are passive, active and acoustic glass break detectors.
Individual identification of detectors
An exact designation of which detector has triggered is possible (see also “Wireless alarm zone”).
Indoor siren
Sounder for indoor use, usually a purely acoustic sounder (in addition to outdoor sirens).
Interior protection
The indoor area of the premises is protected here, especially areas that an intruder most
likely has to enter;
motion detectors and light barriers are usually used here.
Internal alarm
Alarm sounds only within the building. The outdoor sirens do not sound.
Intruder alarm system, burglar alarm system
Alarm system that detects an intrusion and triggers an alarm (“burglar alarm system”).
Intuitive operation
Easy operation of a device using a menu that is logical from the point of view of the user.
Local alarm
If this alarm is triggered the sounders indoors and outdoors sound (outdoors the acoustic alarm (siren) must
stop aer 3minutes if in Germany, but the visual alarm (ashing light) can remain on).
Medical emergency
Personal medical emergency, for which help can be arranged using an alarm.
Motion detectors
Detector used to identify people by thermal movement (PIR – passive infrared), ultrasound (US) or microwave/
radar (MW).
6060 61|
14. Terms and denitions
Opening detector
A detector that identies when a window, door, shutter, garage door, etc. is opened.
Outdoor siren
Sounder for outdoor use, usually designed as a combination sounder (siren + ashing light).
Perimeter protection
All points of access to the premises are monitored, including house doors, terrace doors, cellar doors, skylights
and all windows. Usually magnetic contacts, glass breakage detectors and wireless window locks are used.
The building’s occupants can still move around freely within the building when the alarm system is armed.
The targeted arming of the perimeter is also called “internal arming”.
Perimeter surveillance
Continuous monitoring of large areas of open land around the periphery or the areas used for approaching
the property, e.g. using light barriers and motion detectors on the premises and/or surveillance cameras with
intelligent motion detection.
Programming
Detailed settings for the alarm panel according to the user’s requirements (e.g. zones/sub-areas can be
dened).
Programming
Detailed settings for the alarm panel according to the user’s requirements (e.g. zones/sub-areas can be
dened).
Protected outdoor area
Area outside buildings that is protected from severe weather (such as heavy rain) (e.g. covered entrance area
or terrace).
Proximity / chip key
Electronic “key” for quick access without code entry.
Relay outputs
Switching outputs for external consumers (for controlling light, electrical shutters or other sounders).
Remote access, remote configuration
Control/maintenance/conguration of the alarm panel carried out remotely.
6262
14. Terms and denitions
Sabotage
See “Tampering”
Security frequency band
These frequency ranges (433 MHz or 868 MHz) are approved by the authorities (RegTP) for the security eld.
Signals from wireless earphones, mobile phones, garage door openers, etc. cannot interfere with devices
operating in these ranges.
Seismic sensor
See “Shock detector”.
Shock detector
This detector identies vibrations that occur when an attempt to break in is made.
Signal generator
Sounder that triggers an alarm when it receives a corresponding command from the alarm panel (siren,
strobe, etc.)
Silent alarm
This alarm does not trigger any sounders (indoors and outdoors remains quiet and calm), but a monitoring
station is discreetly notied (intruder is not scared o, rather caught in the act, aggressive intruders are not
provoked, etc.)
Smoke detector (fire alarm)
Optical smoke alarm devices save lives, as they respond to smoke particles in the air (usually poisonous
gases). Heat detectors/heat dierence detectors respond to a maximum temperature (e.g. 65°C) or a rapid
increase in temperature.
Sounder
Device that sends an alarm message acoustically (siren) or visually (ashing light). Even diallers are sounders.
Status feedback
Feedback from the alarm panel to a module (arming device, info module, etc.) about its current status.
Status query
Query sent to the alarm panel about the system status (e.g. by pressing the button on the wireless
remote
control).
6262 63|
14. Terms and denitions
Status
Alarm panel status: either armed or disarmed.
Sub-area
An alarm system can be divided into sub-areas (partitions), each of which functions separately as an individual
alarm system. Each sub-area (e.g. apartment, workshop) can be operated and congured separately and can
contain any number of zones/detectors.
Tampering, tampering protection, tamper
So that the alarm panel and its components when disarmed cannot be tampered with, each component
is monitored for tampering. If a detector is opened or a cable is cut, an alarm is ALWAYS triggered. The
components are usually protected by a cover contact (alarm when detector is opened) and an anti-removal
wall contact.
Technical damage
For example, water damage, escaped gas, etc. (Protection against these things is provided by special danger
detectors).
Telephone dialler
Device used to send alarm messages to an alarm panel via telephone (see AWAG, AWUG). Diallers can be
integrated in alarm panels already or added as additional components.
User guidance
Electronically guided help for operating the alarm panel.
User
Dierent users of the alarm system (e.g. owners, tenants) can be assigned separate rights and user codes.
Wired alarm system
Alarm system with detectors connected to the alarm panel via wires (good idea for new buildings and large
buildings).
Wired detector, wired detectors
Alarm and danger detectors that are connected via wire to the alarm panel.
Wired zone, wired alarm zone
Alarm zone monitored via one or more wired detectors (usually switched in series).
Wireless alarm system
Alarm system with detectors that are connected to the alarm panel wirelessly (advantages: quick and easy
installation, high exibility).
Wireless alarm zone, wireless zone
Zone of the wireless alarm panel that is used to identify and monitor every individual wireless detector.
Wireless control panel
For convenient arming/disarming of the alarm panel, e.g. in another room (in entrance area etc.). The status
can be queried if a bidirectional wireless control panel is used.
Wireless detector
Alarm and danger detectors that are connected wirelessly to the alarm panel.
Wireless key switch
For convenient arming/disarming of the alarm panel without entering a code (using a key).
Wireless range
The max. distance between the alarm panel and wireless detector varies depending on the properties of the
building.
Wireless Remote Control
For convenient arming/disarming of the alarm panel, status query and sending an emergency alarm etc. from
any location.
Wireless window lock
Combination of mechanical window lock and electronic detector.
Zone
Synonym for line, describes a closed circuit to which alarm or tampering contacts are connected, which are
then connected to the alarm panel.
64
14. Terms and denitions
Product name Secvest
Product description Wireless alarm system
Manufacturer ABUS Security-Center GmbH & Co. KG
Environmental class II (EN 50131-1 + A1:2009 Section 7, EN50131-3 Section 7)
Protection class
IP34 (indoor)
Operating temperature 0°C to 40°C
Humidity, maximum Non-condensing average relative humidity 75%
Housing material ABS
Dimensions (W x H x D) 205 x 285 x 48mm
Weight
1453g (excluding batteries)
1543g (including one battery)
90g one battery
Capacity
Zones
IP zones
3
6 (soware version 1.01.00 and higher)
for the ABUS camera models specied see the appendix to
theinstructions for installers titled “Compatible equipment”
Wireless Zones 48
Wired Zones 4 (2-wire FSL/DEOL or 2-wire CC)
2 (4-wire CC)
Wireless control panels
8
External Sirens
Wireless sirens
4
Wired sirens
1
Info modules/internal sirens
∞
15. Technical data
General
15. Technical data 64 65|
6666
WAM
8
Door locks
8
Repeater
4
Outputs
IP Outputs
0
Radio Outputs
32
Wired Outputs
4
Partitions
Four (each with internal arming)
User
50
User names
50 (plus installer name)
User Codes
50 (plus installer code)
Proximity tags (chip keys)
50 (one per user)
Remote controls
50 (one or several per user)
Panic alarm transmitter
50 (one per user)
Medical emergency call transmitter
50 (one per user)
Nursing emergency call transmitter
50 (one per user)
Telephone book
12 contacts
Name
2 telephone nos
1 email
1 IP address
1 VoIP/SIP ID
Calendar timers enabled/disabled
10 time schedules each with 16 events
20 exceptions
Logbook capacity
Up to 600 events
500 mandatory events
100 non-mandatory events
Stored in EEPROM storage (non-volatile memory – NVM) retained for
at least ten years without electricity.
The whole log book stores its records for at least ten years without
electricity.
Note:
The logbook is protected and cannot be deleted by an installer,
administrator or ordinary user.
15. Technical data
6666 67|
15. Technical data
Internal clock
1
Loudspeaker
1
Microphone
1
Voice messages
33 voice messages for each language installed on the alarm panel
5 messages recorded by the user
(Installer mode voice dialler)
12 second site message
8 seconds for each message 1–4
1 memo message (user menu)
30 seconds
58/56 zone names (user menu)
2 seconds for each zone
6 IP zones
48 wireless zones
4/2 wired zones
Internal Siren
1 (integrated piezo sounder)
Communication modules,
plug-in
1
Ports
1x Ethernet
1x a/b
1x USB
1x SD card
Backup batteries
2
Display
3.5", eective area 84mm x 45mm, 240 x 128 pixel monochrome
(greyscale) LCD, white backlighting
Protection and security
Security level Grade 2
(EN 50131-1 + A1:2009 Section 6, EN 50131-3 Section 6)
Environmental class II
(EN 50131-1 + A1:2009)
Tamper protection
(detection/protection)
Type B
(EN 50131-3 Section 8.7)
Wireless components,
dierentiation
16,777,214 (224 -2) dierent IDs per component type
Wireless supervision
Congurable
Access codes
During the initial set-up of the alarm control panel there is neither
a predened standard installer code nor a predened standard
administrator code. These need to be individually assigned in the
set-up wizard.
Quantity of access codes
50 plus one installer
6868
15. Technical data
Access code dierentiation
10,000 code variants with 4-digit codes (0000–9999)
The digits of the code are numbers between 0 and 9.
104 = 10x10x10x10 = 10,000 (combinatorial variation)
1,000,000 code variants with 6-digit codes (000000–999999)
The digits of the code are numbers between 0 and 9.
106 or 10x10x10x10x10x10 = 1,000,000 (combinatorial variation)
Quantity of proximity tags
(chip keys)
50
Proximity tag dierentiation
4,294,967,296 (232, 232)
Temporary authorisation for user
access
There is no facility for providing temporary access (e.g. PIN code or
proximity keyfob which is only valid for a limited time or a specied
quantity).
Locking access/locking codes
Keyboard is locked for 5minutes aer 3 incorrect codes in succession.
Keyboard is locked for 5minutes aer 3 incorrect proximity keyfobs in
succession.
Mechanical keys
Control panels
Wireless key switch
FUBE50060, FUBE50061, FU8165
Mechanical key
dierentiation
30,000
Door locks
Additional door lock
FUFT50010-20, 7010E 7025E
Mechanical key
dierentiation
30,000
Secvest Key
FUSK53030-58080, FUBE5XXXX
Mechanical key
dierentiation
789,024
Web user name length
12 characters
Web user name
dierentiation
8812 (215,671,155,821,681,003,462,656, 88^12, >1,000,000)
All characters can be alphanumeric symbols or special symbols.
A–Z 26
a–z 26
0–9 10
Space apostrophe ():.-!&@+_*# 14
Æ Å Ä Ø Ö Ü (upper case) 6
Æ Å Ä Ø Ö Ü (lower case) 6
88 ∑
Web encryption
HTTPS
SSL version 3/TLS 1.2
S/W < 2.00.00: Signature algorithm: SHA1
S/W >=2.00.00 Signature algorithm: SHA256 (SHA 2)
6868 69|
15. Technical data
Electromagnetic compatibility
EMC – immunity
Complies with EN 50130-4
Electromagnetic compatibility
EMC – interference
Complies with EN 61000-6-3
Electrical safety
Complies with EN60950-1
Power supply
Type of power supply
Type A (EN 50131-1 Section 9 and EN 50131-6 Section 4.1)
Secvest has an integrated power supply unit (Type A). This power supply
unit supplies dierent internal voltages to the circuit board to supply
power to the circuitry.
This power supply unit supplies 13.8V with a maximum of 700mA
atthe 0V/12V AUX output.
Normal voltage/frequency
110V/230VAC, 50/60Hz, (85-265VAC, 50/60Hz)
13.8VDC (13.0–14.5VDC)
Power consumption, maximum
I AC MAX:
430mA rms @ 85VAC
190mA rms @ 230VAC
170mA rms @ 265VAC
Power consumption, nominal
6.9W
6.9W x 24 x 365 = 60kWh per year
55mA rms @ 230VAC
specied with 200mA aux load and fully charged batteries
300mA @ 13.8V
External DC input fault triggered at
12.5V
OK at 12.7V
External PSU
13.0–14.5VDC, at least 1.7A
Power consumption, typical
Alarm panel standby: 100mA
Backlighting o
Backlighting:
High: 100mA
Medium: 40mA
Low: 15mA
Internal siren sounding alarm at maximum volume: 70mA
GSM standby:15mA
GSM in use: 140mA
Battery charging current per battery: 220mA
7070
15. Technical data
Backup power supply
Rechargeable battery
Polymer lithium ion, 7.4V
Capacity
2500mAh, 18.5Wh
Minimum running time in
emergency power mode
(standby time)
More than 12 hours
More than 24hours with optional second battery
Maximum recharging time
Less than 72 hours (EN 50131-1 Section 9 Table 24)
Maximum time to recharge
the battery to 80%
24 hours)
Lower threshold value
of the battery
7.2V
"Flat battery" fault at <7.2V
Deep discharge protection at
6 +/- 0.2V
Aux power supply output
Running on the mains (85–265VAC, 50/60Hz)
13.9Vmax, idle
13.4Vmin, full load (@ 700 mA)
Running on DC input
@13.0V
12.8V max, idle
12.2V min, full load (@ 700mA)
@13.8V
13.6V max, idle
13.0V min, full load (@ 700mA)
@14.5V
14.3V max, idle
13.7V min, full load (@ 700mA)
Aux power supply output fault
triggered at
11.5V
OK from 12.0V
Surge protection
trip voltage
Not given for grade 2
PSU monitoring
Monitoring covers AC and external DC faults.
It noties the alarm panel if the AC or external DC power supply
isdisrupted or fails. The alarm panel will continue running on
thebatteries but the alarm panel and user are informed.
Monitoring covers battery under voltage.
If the battery is at, the alarm panel and user are informed and
thealarm panel gives a warning.
7070 71|
15. Technical data
Fuses
Mains fuse (AC in)
Miniature fuse (micro fuse)
removable
Name
T1AL250V
Characteristic
T = slow blow
Operating current
1 A
Breaking capacity
L = low
Operating voltage
250 V
Design
Glass tube 5x20mm
Wireless signal transmission
Operating frequency
868.6625MHz
In accordance with:
EN50131-5-3 Grade2
EN 300 220-1 V.2.1.1
EN 300 220-2 V.2.1.1
EN 300 220-3 V.1.1.1
Frequency band reserved for applications in the security zone
Modulation
FM
Bandwidth
+/- 10kHz
Narrow band, 25kHz channel separation
Transmission power
10 mW
Antenna
Integrated duplex antenna technology
Range
Indoors: approximately 30m
depending on environmental factors
Outdoors: approximately 100m
Special features
Individual identication
7272
15. Technical data
RFID proximity keyfob reader
Operating frequency
13.56 MHz
In accordance with:
EN 300 330-2
Special features
Individual identication
Connections
L N
Mains connection
110V/230VAC, 50/60Hz, (85-265VAC, 50/60Hz)
L – line, single phase (black or brown)
– protective earth (yellow/green)
N – neutral (blue)
- DC IN +
13.8 V
External PSU input
13.8VDC, external PSU at least 1.7A
See Power supply section for more details
0V 12V
AUX
Voltage output
13.8VDC up to 700mA
Maximum output residual ripple (ripple voltage):
0.2Vp-p
Aux output fault triggered at 11.5V, ok from 12.0V
See Power supply section for more details
+BATT1 ,+BATT2
Battery polymer lithium ion, 7.4V, 2500mAh
OP 301, OP 302
Relay output
Potential-free changeover contact NO/C/NC
Max. contact capacity: 500mA @ 24VAC rms or 30VDC
OP 303, OP 304
Transistor output
Open-drain
Max. contact capacity: 500mA @ 13.8VDC
TR
A negative tamper input
The input is switched to the inactive low state (ground potential)
by the connected siren. The threshold voltages are > 4V for active
and < 3.6V for inactive.
TRB
A negative fault input
The input is switched to the inactive low state (ground potential)
by the connected siren. The threshold voltages are > 4V for active
and < 3.6V for inactive.
10/100 LAN
Ethernet/LAN
Cat5e patch cable, RJ45 male
Connector at each end, suitable for 10/100Base-T
USB TYPE-B
USB Mini-B connector for alarm panel
USB-A connector for PC
Max. length 3m
7272 73|
15. Technical data
A B
Interface for analogue telephone connection to the public
telephone network, a private branch exchange or an integrated
access device (IAD [router] e.g. Vodafone Easybox xyz or FRITZ!Box
vwxy)
Approved for telecommunications in accordance with TBR-21/CTR21
(ETSI ES203021)
> 18V
REN rating 1
PSTN data rates up to 1200bps (V.22)
Micro SD
Secure Digital Memory Card
Micro SD 11mm x 15mm x 1.0mm
4GB Micro SDHC
Z301, Z302, Z303, Z304
Wired Zones
2-wire FSL 2K2/4K7
2-wire FSL 1K/1K
2-wire FSL 2K2/2K2
2-wire FSL 4K7/4K7
2-wire CC
Z301A/Z301T, Z302A/Z302T
Wired Zones
4-wire CC
Resistance ranges specied for idle, alarm and tamper states (in Ohms).
Resistances immediately by the screw terminals.
Recommended cable resistance: must be less than 100Ohms.
2-wire FSL 2K2/4K7
2-wire FSL 1K/1K 2-wire FSL 2K2/2K2 2-wire FSL 4K7/4K7
O/C tampering
8281-∞
2401-∞ 5281-∞ 11281-∞
Alarm
4081-8280
1401-2400 3081-5280 6581-11280
Idle
1760-4080
800-1400 1760-3080 3760-6580
S/C tampering
0-1759
0-799 0-1759 0-3759
4-wire CC
2-wire CC
Open/alarm/tampering
1001-∞
1001-∞
Closed/idle
0-1000
0-1000
7474
15. Technical data
Communication
Communication channels
a/b interface
Interface for analogue telephone connection to the public
telephone network, a private branch exchange or an integrated
access device (IAD)
Ethernet
10/100 LAN
GSM
Plug-in module, optional
Quad-band GSM: 850/900/1800/1900MHz
Communication methods
Web server
Web access, app and ABUS server
ARC/ESCC reporting
Receiver
2 Tel, 2 IP
Protocols
Analogue
Fast Format, Contact ID (CID), SIA 1, SIA 2, Ex SIA 3, Ex SIA 3 V2,
CID in SMS
IP
DC-09 (SIA IP) with Fast Format, Contact ID, SIA
TCP, unencrypted
Note:
For details, see the appendix to the instructions for
installers entitled "ARC (ESCC) reporting protocol formats"
Nursing emergency call
Receiver
2 Tel
Protocols
Scancom, Scanfast, Tunstall
Protocol Token
FF “SCN-S8”
CID “ADM-CID”
SIA 1, SIA 2, SIA 3, Ex SIA 3,
Ex SIA 3 V2 “SIA-DCS”
7474 75|
15. Technical data
Voice dialler
Receiver
8 Tel or VoIP/SIP ID
DTMF detection VoIP/SIP
Acknowledgement RFC 2833
Codec VoIP/SIP
PCM G711 A law (RTP AV Prole 8)
ITU-T G.711 PCM A-Law audio 64kbit/s
Reference RFC 3551
SMS
Receiver
8
PSTN SMS protocol TAP 8N1, TAP 7E1, UCP 8N1, UCP 7E1, ETSI Protocol 1
Email
Receiver 8
Remote control by telephone Yes
ATS Alarm transmission system
Categories and classications
ATS (Alarm Transmission System)
categories, SPT (Supervised Premises
Transceiver) classication
The alarm panel contains an integrated SP2 (ATS2)
communicator to full the requirements of EN50131 for security
grade 2.
The alarm transmission system is compliant with
EN50136-1:2012 as an SP2 (ATS2) communicator.
The alarm panel supports options A, B and C for grade 2 as
given in Table 10 in EN50131-1:2006+A1:2009.
Classication of transmission time D2 -> SP2
Transmission time, maximum
values M2 -> SP2
Classication of notication time T2 -> SP2
Classication of availability
A0 (no requirement)-> SP2 (optional)
There is no method for achieving compliance with EN 50136-
1:2012, 6.7.3 (non-availability of the alarm transmission system)
because A0, no requirement.
Security to prevent removal
S0 (no measures) -> SP2 (optional)
There is no method for achieving compliance with
EN50136-1:2012, 6.7.2 (redundancy) because S0, no measures.
Information security
I0 (no measures) -> SP2 (optional)
There is no method for achieving compliance with
EN50136-1:2012, 6.8.3 (information security) because I0,
nomeasures.
7676
15. Technical data
Monitoring a/b, Ethernet and GSM
See the instructions for installers, pages 140 and 141
Installer mode -> Communication -> Comm. options -> Comm.
path fault response
Ethernet, PSTN (a/b), GSM
Installer mode -> Communication -> Comm. options -> Comm.
path fault delay
Ethernet, PSTN (a/b), GSM
Handshaking procedure
Mode/procedure:
Transfer
(EN 50136-2 Section 6, Operation)
Other
Conguration
Web browser via the integrated web server or directly on the alarm
panel
Declarations of compliance
for the FUAA50000, FUAA50010, FUAA50100 and FUAA50110 Secvest wireless alarm panel systems
Standards with which the alarm panel claims compliance
EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-5-3:2005+A1:2008
EN50131-6:2008+A1:2014
EN50131-10:2014
EN50136-2:2013
INCERT TO31 2014 edition
Security level: Grade 2
Environmental class: Class II
If the alarm panel has been installed correctly, the Secvest will be compliant with EN50131 Grade 2.
The Secvest is compliant with EN50131-1 and EN50130-5 environmental class II.
Power supply is compliant with EN50131-1:2006+A1 2009 Section 9 and EN50131-6 if the alarm panel has
been installed correctly.
The alarm transmission system (integrated SP2 [ATS2] communicator) is compliant with EN50136-1:2012
asanSP2 (ATS2) communicator.
At Grade 2 the integrated SP2 (ATS2) communicator provides a compliant communicator for the Secvest
onthe condition that
a) it is installed as specied in the installation instructions
b) the connected PSTN, LAN and GSM work normally
c) the alarm receiving centre has the right equipment.
7676 77|
15. Technical data
The FUMO5000X GSM module can be used as a supplementary communicator for Grade 2.
The alarm panel supports options A, B and C for grade 2 as given in Table 10 in EN50131-1:2006+A1:2009.
If the installer selects a non-compliant conguration the compliance label must be removed or corrected.
Third party verication of compliance was carried out by ANPI.
7878
16.1 Manual restart (switching o and switching back on)
S/W >=1.01.00
This is helpful for some problems, to reset the alarm panel to a dened initial state. All the settings and
congurations are retained.
Note
A restart is only possible when
all partitions are "disarmed" and
the alarm panel has completed all important communications, transmissions and actions.
There are three ways to do this
[1] In the user menu on the alarm panel when logged in as administrator
[2] In the user menu on the web server when logged in as administrator
[3] On the alarm panel by pressing the "Up" and "Down" navigation keys
[1] Alarm panel user menu
User menu -> Conguration -> Functions -> Restart alarm panel
You can use this to restart the alarm panel manually.
Note
This menu item is only visible to the administrator, i.e. the administrator must be logged into the system.
Select "Restart alarm panel" by pressing the "Change" menu key.
You are prompted for conrmation.
Press the "Yes" menu key.
At this point you can still cancel the restart.
Press "Back".
[2] Web server user menu
User menu -> Conguration -> Functions -> Restart alarm panel
You can use this to restart the alarm panel manually.
Note
This menu item is only visible to the administrator, i.e. the administrator must be logged into the system.
16. Troubleshooting
16. Troubleshooting
79|7878
Click on "Restart alarm panel".
You are prompted for conrmation.
Click on "Restart alarm panel" again.
At this point you can still cancel the restart.
Click on "Cancel restart".
The restart is displayed as shown below.
16. Troubleshooting
8080
16. Troubleshooting
Aer the restart you are automatically logged out of the web server. If you wish to continue working on the
web server, please log in again with your user name and password.
[3] Alarm control panel – "Up" and "Down" navigation keys
Hold down the "Up" and "Down" navigation keys simultaneously for longer than ve seconds.
Installer in installer mode:
If the "Up" and "Down" navigation keys are held down simultaneously for longer than ve seconds,
the alarm panel is restarted immediately
Administrator in the user menu:
If the "Up" and "Down" navigation keys are held down simultaneously for longer than ve seconds,
the alarm panel is restarted immediately.
Alarm panel in standby mode:
If the "Up" and "Down" navigation keys are held down simultaneously for longer than ve seconds,
an access code entry screen appears.
Once a valid installer code or administrator code has been entered and subsequently conrmed with
"Yes" the alarm panel is restarted.
8080
16. Troubleshooting 81|
16.2 GSM manual test call, prepaid
Danger
Note
If you use a prepaid SIM card on a prepaid tari ,
e.g. CallYa, Xtra or Magenta Mobil-Start,
Please carry out a GSM test call and/or send a GSM test text message every month or every three months.
If you do not use the GSM network for a long time it can be that:
the GSM alarm call does not work
the GSM alarm text message does not work
and the card is temporarily locked by the network operator.
The card can no longer connect to the GSM network.
You will see a fault noti cation on the alarm panel.
This means it is not possible to trigger an alarm call or an alarm text message. Furthermore, the alarm panel
can no longer be contacted via GSM.
If the network is not used for a long time the operator may do this with contract SIM cards as well.
Therefore, please also carry out a GSM test call and/or send a GSM test text message every month or every
three months.
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg5
86444 Ang
Germany
Tel. +49 82 07 959 90 0
Fax +49 82 07 959 90 100
info.de@abus-sc.com
abus.com V3.00.03
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus Secvest V3 - FUAA50510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus Secvest V3 - FUAA50510 in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Secvest V3 - FUAA50510

Abus Secvest V3 - FUAA50510 Quick start guide - English - 16 pages

Abus Secvest V3 - FUAA50510 Installation Guide - English - 424 pages

Abus Secvest V3 - FUAA50510 Quick start guide - German, Dutch - 16 pages

Abus Secvest V3 - FUAA50510 User Manual - Dutch - 436 pages

Abus Secvest V3 - FUAA50510 User Manual - Dutch - 82 pages

Abus Secvest V3 - FUAA50510 Quick start guide - Danish, French, Italian, Polish, Swedish, Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info