756181

Abus fumo50020 Manual

56
Zoom out
Zoom in
Previous page
1/187
Next page
52
Exit the programming mode by pressing ESC/DEL.
The LED for the power supply lights up/flashes and the fault LED
lights up. The accessory module beeps at short intervals.
Close both tamper contacts of the WAM and wait until it emits
a double tone.
Note: In order to train the wireless cylinder to the accessory
module, the dip switch 1 must be set to ON.
2. To train the wireless cylinder to the accessory module, proceed
as follows:
Set dip switch 1 to ON.
In the main programming menu, select item 1 (LED 1 lights
up).
Confirm by pressing SET.
The LEDs show the state of the trained wireless detectors. If
an LED flashes, this indicates that the channel is in use. If the
LED is off, a detector can be trained in this channel.
Send a signal from the cylinder. If the signal is received, the
accessory module assigns this detector to a new channel. The
LED of this channel starts to flash. When the signal has been
successfully trained, the accessory module beeps twice.
Repeat the steps above to train another cylinder.
After training all detectors, exit programming mode by pressing
ESC/DEL twice.
The LED for the power supply lights up/flashes and the fault LED
lights up. The accessory module beeps at short intervals.
Close both tamper contacts of the WAM and wait until it emits
a double tone.
3. Remove all jumpers for controlling the outputs and connect the
accessory module to the alarm centre as described under point
7.3.6.
The relay outputs are opened when the wireless cylinder is
rotated in the close direction and the alarm system is activated.
The relay outputs are closed when the wireless cylinder is rotated
in the open direction and the alarm system is deactivated.
Note: Invert the outputs as detailed under point 7.3.6.
The outputs are stable when switched, meaning the zone of
the centre must be programmed as a block lock.
In mode 1 with dip switch 8 set to OFF, the detector channels
are each allocated to an output in pairs. This means that
channels 1 and 2 control output 1, channels 3 and 4 control
output 2 and so on.
In mode 2 with dip switch 8 set to ON, four detector channels
are allocated to an output. This means that channels 1, 2, 3
and 4 control output 1 and channels 5, 6, 7 and 8 control
output 2. The other outputs have no function.
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus fumo50020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus fumo50020 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info