588203
11
Zoom out
Zoom in
Previous page
1/54
Next page
11
Condition Cause Solution
01
The voltage of the
battery is lower than
10V after 10 minutes
charged.
There is short circuit in the battery. Replace the battery. Dispose of the
defective battery in a suitable manner.
There is load connected to the
battery.
Disconnect the load from the battery.
The voltage of the bat-
tery is lower than 13V
when the battery goes
into oat charge.
Recondition the battery.
02
The voltage between
the two clamps is higher
than 19V.
The voltage between the two
clamps is too high.
Check the battery. The voltage of
battery should be in the range of 12V
to 14V.
03
The charge current is
too high.
This happens when an external
voltage source is connected to the
battery during charging process.
Please disconnect battery from any
external components.
04
The temperature of the
charger is too high.
This charger ambient temperature
is too high.
Clean dirty ventilation openings or re-
move objects covering the unit. Place
the unit in a cooler location.
05
The battery charger
does not go into oat
charge.
The charging current is too low. Choose the higher current to charge
the battery.
Bad battery. Replace the battery. Dispose of the
defective battery in a suitable manner.
2. Reverse Polarity LED Indicator - when the battery clamps are connected incorrectly the red LED illumi-
nates.
3. Battery Recondition Indicator - when the battery is reconditioned, the yellow LED illuminates. The charger
will recondition the battery only when the battery is in a state of “deep discharge”. It cycles every 4±0.5h until
the battery is no longer “deep discharged”. If it cycles 5 times and the condition has not changed, there will be
the code F01 present on the display panel, indicating an error. Please replace the battery.
4. Charging State LED Indicator - when battery is charged at a constant current or a constant voltage, the
green LED ashes. When the battery is fully charged or goes into oat charge, the green LED illuminates.
5. Current Indicator - When the display panel indicates the present current, the current LED indicator illumi-
nates.
6. Voltage Indicator - When the display panel indicates the present voltage, the voltage LED indicator illumi-
nates.
7. Battery Capacity - When the display panel indicates the battery capacity, the LED indicator illuminates.
Code Condition
LO The capacity is lower than 50%
80 The capacity is around 80%.
FUL Battery is full charged
8. Display Button Switch - You can choose the display mode on the panel by pressing the button.
9. Automatic – The charger automatically selects the correct charging current for your battery
10. 2A Charge current Indicator – The charging current is set to 2A.
11. 8A Charge current Indicator – The charging current is set to 8A.
12. 12A Charge current Indicator – The charging current is set to 12A.
13. Charging Current Select Button – select the charging current for your battery type, for your reference see
the table below:
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Absaar HF1212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Absaar HF1212 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info