Manual Absaar BBL 1205 (page 8 of 14) (Dutch)

606533

8

Zoom out

Zoom in

Previous page

1/14

Next page

8

DIRECTIONS OF USE

BATTERY CHARGERS MODEL RANGE

BBl

READ THESE INSTRUCTIONS BEFORE

USING THE CHARGER

Selection switch

ASSEMBLY

OFTHE

BATTERY CLIPS

Battery clip

(+) colour red:

Push red clip insulation sleeve

over the red

(+) lead insulation.

Clip the cable onto the battery

clip. Push clip insulation further

on

the clip.

Battery

-clip

(-), colour black:

Push black clip insulation

sleeve over the black (-) lead

insulation. Clip the cable onto

the battery clip. Push clip

insulation further on the clip.

CHANGING FUSE

When replacing the blade fuse

first disconnect the mains plug.

After that unclip the battery

clips from the battery poles.

The fuse is situated clearly

visible in the front plate.

Remove the defect blade fuse

(fuse wire interrupted) and

replace with a fuse of the same

amperage (20 amp).

To

replace the fuse, insert the

blade of a screwdriver

in

the

gap between the fuse and the

fuse holder. Use the

screwdriver as a lever.

DO NOT USE FORCE TO

CHANGE THE FUSE!!

GUARANTEE DOES NOT

COVER A

BLOWN FUSE!

CAR - MOTORCYCLE

(12 Volt)

Depending on the model it

is

possible to have a charger

equipped with a selection

switch CAR - MOTORCYCLE.

If the switch is setted on

Motorcycle the result will be a

lowering

of

the charging

current for charging a battery

with capacity of

5-15 Ah.

NORMAL - FAST CHARGE

Depending on the model it is

possible to have a charger

equipped with a selection

switch NORMAL-FAST

CHARGE.

If the switch is setted on

NORMAL the result will be

charging with a reduced

charging current and longer

charging time. Normal charge

is a special battery saving

process.

In the switch setting FAST

CHARGE it is possible

to

recharge weak starting

batteries in a short time so far

that starting of a car is again

possible.

IMPORTANT!!!

Precharge

deeply discharged batteries

with high capacity (Ah) always

in switch setting NORMAL for

half an hour.

VOLTAGE SELECTION

SWITCH

The voltage selection switch

6

volt - 12 volt makes it possible

to use the charger for

6 and 12

volt batteries.

Charging voltage and battery

voltage have always to be the

same value.

Check before the charging

process the battery voltage.

Batteries with 3 cells are 6 volt

and batteries with

6 cells are

12 volt.

CHARGING CURRENT

INDICATOR

AMMETER

The battery charging rate is

shown with a current measure -

ammeter.

The charger will give a high

charging current when

charging commences. The

needle will be in the right part

of the ammeter. The charging

current will become lower

when charging progresses. The

needle will fall back

in

the left

part of the ammeter scale and

it will indicate in that position

the end of the charging

process. The battery is

fUlly

charged.

Depending on the model it is

possible to have an electronic

charging control indicator.

ELECTRONIC CHARGING

CONTROL INDICATOR LA3

The charging indicator is

situated in the frontside of the

charger. It indicates via

coloured LED diodes the stage

of the battery charger.

LED RED LIGHTS UP

It means that the charger is

connected in the right way to

the battery poles (+,-). The

charging process can be

started by connecting the

charger to the mains. The red

light remains lit

up

during the

1

How do I know when the battery is fully charged my charger only has an amp dial display Submitted on 24-7-2024 at 20:14
Reply Report abuse
Does the charger have a trickle charge for use with a 12v lead acid battery
Submitted on 11-6-2020 at 12:54
Reply Report abuse
I have a absaar bbl 1205 and the main power switch has 3 connections on it please tell me which colour wire goes to which terminal please Submitted on 17-11-2017 at 23:15
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Absaar BBL 1205 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Absaar BBL 1205 in the language / languages: Dutch as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info