588214
12
Zoom out
Zoom in
Previous page
1/43
Next page
12
c. Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.
d. Add distilled water in each cell until battery acid reaches level specified by battery
manufacturer. This helps purge excessive gas from cells. Do not overfill. For a battery without
cell caps, carefully follow manufacturer's recharging instructions.
e. Study all battery manufacturers specific precautions such as removing or not removing cell
caps while charging and recommended rates of charge.
f. Determinate voltage of battery by referring to car owner's manual and make sure that output
voltage selector switch is set at correct voltage. If charger has adjustable charge rate, charge
battery initially at lowest rate.
7. CHARGER LOCATION
a. Locate charger as far away from battery as the DC cable permits.
b. Never place charger directly above battery being charged; gases from battery will corrode and
damage charger.
c. Never allow battery acid to drip on charger when reading gravity or filling battery.
d. Do not operate charger in a closed-in area or restrict ventilation in any way.
e. Do not set a battery on top of charger.
8. DC CONNECTION PRECAUTIONS
a. Connect and disconnect DC output clips only after removing AC cord from electric outlet.
Never allow clips to touch each other.
b. Attach clips to battery and chassis
Follow these steps when battery is installed in vehicle. A spark near battery may cause battery
explosion. To reduce risk of a spark near battery:
a. Position AC and DC cords to reduce the risk of damage by hood, door, or moving engine
parts.
b. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.
c. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger
diameter than NEGATIVE (NEG, N, -) post.
d. Determine which battery post is grounded {connected) to the chassis. If negative post is
grounded to chassis (as in most vehicles), see (e). If the positive post is grounded to the chassis.
e. For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to
POSITIVE {POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clip to
vehicle chassis or engine block away from battery. Do not connect clip to the carburetor, fuel
lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine
block.
f. For positive-grounded vehicle, only connect NEGATIVE (BLACK) clip from battery charger
to NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE (RED) clip to
vehicle chassis or engine block away from battery. Do not connect clip to the carburetor, fuel
lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine
block.
h. See operating instructions for length of charge information.
Follow these steps when battery is outside vehicle. A spark near battery may cause battery
explosion. To reduce risk of a spark near battery:
a. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Absaar 100602-1206CS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Absaar 100602-1206CS in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info