621595

AA-Drill 77315 Manual

19
Zoom out
Zoom in
Previous page
1/39
Next page
17
The work must be clamped firmly while drilling any tilting, twisting or shifting results
not only in a rough hole, but also increases drill beakage. For flat work, lay the
piece on a wooden base and clamp it firmly down against the table to prevent from
turning. If the piece is of irregular shape and cannot be laid flat on the table it
should be securely blocked and clamped.
C Boring in wood twist drills:
Although intending for metal drilling may also be
used for boring in wood, machine spur bits are generally preferred for working in
wood. They cut a square bottom hole and are designed for removal of wood chips.
Do not use hand bits which have a screw tip. At drill press speeds they turn into
the wood so rapidly as to lift the work off the table and whirl it.
4.ASSEMBLY
1. Open the box and take out the base and place it on a flat floor.
2. Take out the column with colomn bracket and screw it on the base.
3. Take out the head frame and assemble to the column.
4. Then use the allen key for tightening the set screw.
5. Bring out the handle, then screw it in the round head.
5. INSTALLATION
1. After installing the drill press, use the kerosene to wash out the anti-rust oil
which had been coated in the factory. Then wipe it with lubricant oil.
2. Install your drill press in flat, study floor or surface.
a. Check if the drill press is shaking when the motor is switched “ON”.
b. Check the table bracket if it is moving smoothly up and down.
c. Check if the spindle shaft moves smoothly.
6. LUBRICATION
The ball bearings in the quill and V-belt pulley are grease-scaled for life. Pull quill
down to maximum depth and oil moderately once every 3 months.
Slide bars: remove motor belt and push cam handle towards the motor. Oil right
and left slide bars lightly every 2 months. Grease table bracket if cranking
becomes difficult.
7.0 OPERATING TEST
a. Open the belt cover and release the left & right side cam shaft set handle. Then
move the belt handle backward until the belt has its right tension.
b. The rotation speed of spindle shaft can be charged by refering to the chart list
which is attached inside the belt cover, then you can push the belt handle to
adjust the V-belt to its right tension and set back the two sides cam shaft set
handle.
c. Plug the electric socket to the outlet and press “ON” the switch. Then the
spindle shaft will rotate clockwise.
d. If the spindle shaft rotates counter-clockwise, it means the wiring connection is
wrong, so turn off the switch and change the connection, after changing the
spindle shaft will rotate clockwise.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AA-Drill 77315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AA-Drill 77315 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info