671771
46
Zoom out
Zoom in
Previous page
1/68
Next page
Installation and Service Manual Upsilon-Series
46
ParamMode Parameterchapter
PARA
factory
setting
Description Range
Cascadeparam.
Cascade parameters
P100 0 Domestic hot water facility 0-8
0: no DHW
1: Solo boiler with 3-wa
y
valve
2: n.a.
3: Solo boiler with c
y
linder loadin
g p
um
p
P4 and 3-wa
y
valve
4: n.a.
5: After low loss header: DHW after LLH with c
y
linder
p
um
p
P2 and P3=of
f
6: After low loss header: DHW after LLH with c
y
linder
p
um
p
P2 and P3=on at heat demand CH
7: After low loss header: DHW loadin
g
s
y
stem after LLH with c
y
linder loadin
g p
um
p
P2, P4 and P3=of
f
8: After low loss header: DHW loadin
g
s
y
stem after LLH with c
y
linder loadin
g p
um
p
P2, P4 and P3=on at heat demand CH
P101 0 Heating 0-3
0: 0÷10V not active
1: 0÷10V= load control (see further P205 until 210)
2: 0÷10V= temperature control (see further P215 until 220)
3: Showroom position
P104 0 Outside sensor T4 0-1
0: autodetect
1: connected
P105 0 Common flow sensor T10
0-1
0: autodetect
1: connected
P106 30 Min. Setpoint T10 0-60
P107 0 Min.Setpoint function T10 0-2
0: off
1: minimum value setpoint at heat demand CH
2: continuously minimum value setpoint
P109 0 Correction outside sensor -5 - 5
P111 20 CH-set gradient-reference 0-60
P112 1,0
CH-set gradient in °C/10sec in steps of 0,1°C
0-10
P114 1 Number of boilers in cascade (To be set manually!)
1-8
P121 1 Relay function Propane/External heating source 0-1
0: Onl
y p
ro
p
ane
1: On/Off external heatin
g
source
P125
1
DHW i it
0 1
NOTE:
Option 6 and 8 not for Low Temerature
systems, unless separately controlled
ADVICE for using 0-10V:
Choose option 2 for a balanced
behaviour of boiler control.
P125 1 DHW priority 0-1
0:No
1: Yes
P157 0 OpenTherm error bit selection 0-2
0: Onl
y
error
s
1: Errors and blockin
g
s
2: Errors, blockin
g
s and messa
g
e
s
P158 0 Error relay selection 0-2
0: Only error
s
1: Errors and blockin
g
s
2: Errors, blockin
g
s and messa
g
e
s
P170 90 Switch on moment relay external heating source 0-100%
When demand is higher then adjusted value the external heating source will be switched on
P171 85 Switch off moment relay external heating source 0-100%
When demand is lower then adjusted value the external heating source will be switched off
P203 2 Overrun time secondary pump P3 in minutes 0-60
At P101 = 1 (Load control):
P205 2
0-10V, load voltage to have minimum heat demand (P208 power) (If P101=1)
0-10
P206 9,5
0-10V, load voltage to have maximum heat demand (P207 power) (If P101=1)
0-10
P207 100%
0-10V, load maximum power (dynamic range) (If P101=1)
0-100
P208 0%
0-10V, load maximum power (dynamic range; 0% is minimum power) (If P101=1)
0-100
P209 1
0-10V, load heat demand when input voltage> (If P101=1)
0-5
P210 0,5
0-10V, load no heat demand when input voltage< (If P101=1)
0-5
At P101 = 2 (Temperature control):
P215 2
0-10V, load voltage to have minimum heat demand (If P101=2)
0-10
P216 9,5
0-10V, load voltage to have maximum heat demand (If P101=2)
0-10
P217 1
0-10V, load heat demand when input voltage> (If P101=2)
0-5
P218 0,5
0-10V, load no heat demand when input voltage< (If P101=2)
0-5
P219 30
0-10V, temperature setpoint at minimum input voltage (If P101=2)
10-90
P220 85
0-10V, temperature setpoint at maximum input voltage (If P101=2)
10-90
P252 2 Slope heating line (K-factor) 0,1 - 9,9
P256 2 Hysteresis Summer/Winter in °C (if T4 was detected) 0-10
P266 2 Switch on delay at heat demand in minutes 0-10
P267 168 Boiler sequence for boilers in cascade in hours 1-255
P283 1 Frost protection 0-1
0: T10 and P3 not active
1: T10 and P3 active
1
:
T10
an
d P3
ac
ti
ve
P284 -5 Switch on temperature frost protection in °C -40 - 20
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith Upsilon UB-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith Upsilon UB-110 in the language / languages: English as an attachment in your email.

The manual is 9,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith Upsilon UB-110

A.O. Smith Upsilon UB-110 User Manual - English - 2 pages

A.O. Smith Upsilon UB-110 Additional guide - English, Dutch - 2 pages

A.O. Smith Upsilon UB-110 Installation Guide - Dutch - 72 pages

A.O. Smith Upsilon UB-110 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info