503271
66
Zoom out
Zoom in
Previous page
1/126
Next page
Fig. Terminal block
A. Screws
B. Cover
C. Terminal block
7.8.1 Preparation
In preparation, you must first remove the two covers, and the cover of the electrical
section.
Undo the screws of the covers.
Carefully remove the covers from the water heater.
The electrical section is now visible.
Loosen the 2 screws (A) and remove the cover (B) from the electrical section.
The connector block (C) is now visible.
Note
Consult the table for the connections and consult the electrical diagram for the electrical
component connections.
Mains voltage Isolating transformer Alarm Out Program
controlled
External BUS
Primary Secondary
pump ON/OFF link
N L
A
N L
1
A
N L
2
A
X
1
X
2
A
N L
3
A
X
3
X
4
X
5
X
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 to 20 21 22 23 24
7.8.2 Mains power
Note
The water heater is supplied without a power cable and isolator.
Use a power cable with cores of at least 3 x 1,0 mm
2
and a double-pole isolator with a
contact gap of at least 3 mm.
Connect the water heater to the mains power supply:
Connect neutral (N), live (L) and earth (A) of the power cable to terminals 1 thru 3 of
the terminal block as shown in the table (see section 7.8.1).
Fit the power cable in the strain relief.
Connect the power cable to the isolator.
If you have no more connections to make:
Fit the cover on the terminal block.
Fit the covers onto the water heater.
1.
2.
3.
n
n
1.
2.
3.
4.
-
-
66 Installation, Maintenance and Service part
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith SGS 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith SGS 30 in the language / languages: English as an attachment in your email.

The manual is 5,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith SGS 30

A.O. Smith SGS 30 User Manual - German - 128 pages

A.O. Smith SGS 30 Usermanual and installation guide - Dutch - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info