671746
51
Zoom out
Zoom in
Previous page
1/64
Next page
51
Figuur 8-10 - NTC curve temperatuursensoren
8 - ONDERHOUD
8.10 - Procedure voor het aftappen van
het warmwaterdoorstroomtoestel
Ga voor het legen van het toestel als volgt te werk (zie
guur 5-5):
1.- sluit de afsluiters "10" en "3";
2.- sluit een afvoerpijp op de aftapkranen "4" aan;
3.- open de aftapkranen "4";
4.- in geval van kans op bevriezing wordt aangeraden om
al het water uit de warmtewisselaar te verwijderen door
met een compressor lucht in een kraan te blazen (druk
minder dan 3 bar).
8.11 - Procedure voor de
ventilatortestmodus
De ventilator kan worden ingeschakeld door de parameter
2010 in het Installatiemenu (zie paragraaf 7.8) op
"Fan" [ventilator] te zetten. Zet om naar de normale
bedrijfsomstandigheden terug te keren parameter 2010
weer op OFF.
8.12 - Procedure voor de testmodus voor
het minimum- en maximumvermogen van
de gasbrander
Werking van het toestel op minimum- en maximumvermogen
kan worden geforceerd. Ga als volgt te werk:
1.- open parameter 2010 in het Installatiemenu (zie
paragraaf 7.8);
2.- zet parameter 2010 op de volgende waarde:
a) LOu voor geforceerde werking van het toestel op
minimumvermogen;
b) Ign voor geforceerde werking van het toestel op
ontstekingsvermogen;
a) HIgH voor geforceerde werking van het toestel op
maximumvermogen;
a) rEg voor geforceerde werking van het toestel op
maximumvermogen.
4.- zet om de geforceerde werking te stoppen parameter
2010 op OFF en druk op de toets RESET.
8.13 - De ionisatiestroom controleren
In iedere bedrijfsstatus, ook tijdens het controleren van
het minimum- en maximumvermogen zoals beschreven
in paragraaf 8.12, kan de ionisatiestroomwaarde
worden geraadpleegd via parameter 1008 in het
Gebruikersmenu (paragraaf 7.7). Deze waarde moet bij
minimumvermogen tussen 1,5 en 3 uA (microampère)
liggen en bij maximumvermogen tussen 5 en 8 uA.
8.14 - Procedure voor het testen van de
watertemperatuursensor
De temperatuursensoren bevinden zich in het
warmtewisselaardeel van het toestel. De elektrische
weerstand tussen de twee contacten van de sensor moeten
met guur 8-10 overeenkomen.
De temperatuursensoren zijn: 1001, 1002, 1005,
1006 en 1007. Zie voor de correcte plaatsing hiervan
guren 3-1, 3-3 en 3-4.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith Instano ICW 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith Instano ICW 60 in the language / languages: Dutch as an attachment in your email.

The manual is 8,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith Instano ICW 60

A.O. Smith Instano ICW 60 Usermanual and installation guide - English - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info