671738
52
Zoom out
Zoom in
Previous page
1/92
Next page
8.9.1 Filling
Refer to the installation diagram (see section 8.3) when you fill the water heater:
Open the stop valve (11) in the hot water supply pipe.
If applicable, open the stop valves (4) of the circulation pipe (C).
Make sure that the drain valve (9) is closed.
Open the nearest hot water draw-off point (14).
Open the stop valve (4) of the cold water supply pipe (A). Cold water flows into the
water heater.
Fill the water heater until a full water jet flows from the nearest draw-off point. The
water heater is completely full.
Open all draw-off points to bleed the entire installation of air.
The water heater is now under water supply pressure.
Make sure that no water comes out of the expansion valve (15) or the T&P valve (3).
If water comes out:
Examine if the water supply pressure is greater than the specified value in the
Technical details (see section 13.1). If necessary, install a pressure reducing
valve (1).
Examine if the expansion valve in the protected cold supply set-up is installed
correctly and is not defect. If necessary, replace the expansion valve.
8.9.2 Air pressure differential
Check the air pressure differential across the air pressure switch:
Disconnect hose H of the air proving switch and connect this side of the hose to the
+ of the pressure gauge.
Disconnect hose L of the air pressure switch and connect this side of the hose to the
- of the pressure gauge.
Turn the water heater on and set the water heater in OFF mode, refer to Turn on
the water heater (see section 4.2).
Note
Make sure that the water heater is not in ON mode or in External ON mode.
Set parameter 201 to FAn, refer to
Settings (see section 10).
Read the pressure value from the meter.
Compare the measured value to the value from the table (see section 13.1).
Note
When the air pressure differential is not correct, refer to Displayed errors (see section
12.1.2), error F03.
Set parameter 201 to dIS, refer to
Settings (see section 10).
Press [RESET].
The water heater goes into OFF mode.
Set the control switch on the side of the water heater to 0 to turn off the water
heater.
Disconnect the pressure gauge.
Reconnect the hoses of the air proving switch and the gas valve.
1.
2.
3.
4.
5.
6.
7.
8.
-
-
1.
2.
3.
n
4.
5.
6.
n
7.
8.
9.
10.
11.
52 Installation, Maintenance and Service part
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith Innovo IR 20-200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith Innovo IR 20-200 in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith Innovo IR 20-200

A.O. Smith Innovo IR 20-200 Usermanual and installation guide - German - 4 pages

A.O. Smith Innovo IR 20-200 Usermanual and installation guide - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info