671748
12
Zoom out
Zoom in
Previous page
1/28
Next page
12
12
2. FOR THE INSTALLER
2.1 Installation instructions
This water heater must be fitted in a
location which will permit the provision
of an approved flue system and
adequate ventilation.
A service clearance of 15 cm at the
sides and rear of the unit and 60 cm at
the front of the unit should be allowed
for ease of servicing. Adequate
distance must be allowed between the
top of the unit and any obstruction or
ceiling to allow the flue baffle and
anode to be inspected, cleaned or in the
case of the anode replaced if
necessary.
The water heater must stand on a
level surface resistant to heat and with
sufficient strength to support the weight
of the unit when full of water.
This water heater must not be
installed in a bath room, bedroom or in a
cupboard opening on to such rooms.
This water heater must not be installed
in any area where flamable materials
are used or stored.
Insufficient ventilation may give rise
to a risk of fire, explosion or
suffocation. If in doubt consult the
national and local regulations governing
the installation of gas appliances or
your local British gas service depart-
ment.
2.1.1 Installation
The installation of this water heater
should be carried out by a suitably
qualified competent person. It is a
criminal offence for unqualified persons
to install gas equipment.
Installation should be carried out in
accordance with all local authority and
building regulations, local water
authority and fire regulations and the
following British standards: 5440, 5546,
6644, 6700, 6798 and 6891.
Some chemicals produce vapours
which can cause rapid failure of
thermocouples, burners and storage
tanks if they are drawn into the
combustion air supply.
Therefore if this water heater will
be used to supply hot water to:
- hairdressers,
- dry cleaners
- industrial degreasing processes
or any other area where
compounds containing halogens are
used and stored, care should be taken
that all primary and secondary air is
drawn from outside atmosphere free of
such contaminents.
For further advise contact A.O.
SMITH.
2.1.2 Water connections
A.O. Smith water heaters are
suitable for connection to vented,
unvented and pumped pressurised
systems. In each case appropriate
valves and fittings should be used to
ensure the system complies with the
requirements of the water by laws, and
appropriate building regulations.
When fitting it is essential the rules
of 'good practice' are applied at all
stages of installation.
Vented systems
If the water heater is to be
connected to a cold feed tank or cistern
the hot water supply pipe must include
an open vent which discharges over
the cold feed cistern. The cold feed
cistern must have an actual capacity of
greater volume than the hourly recovery
rate of the water heater(s) which it
supplies.The minimum actual capacity is
50 gallons or 227 litres.
Unvented
To install an A.O. Smith water
heater on an unvented cold water
supply system a kit of valves and
fittings listed by the water research
centre and complying with part G3 of
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith EQ 380 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith EQ 380 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith EQ 380

A.O. Smith EQ 380 User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info