503230
53
Zoom out
Zoom in
Previous page
1/74
Next page
Instruction manual BFM 53
gis
9 Starting and running
9.1 Introduction
Topics covered in this chapter:
Starting the appliance;
The appliance's heating cycle
.
9.2 Starting the appliance
Start the appliance as follows:
1. Fill the appliance (5 "
Filling").
2. Open (3.5 "
Installation diagram") the manual gas
valve.
3. Switch on the power to the appliance using the
isolator between the appliance and the power
supply.
4. Put the appliance in ON mode by setting the
ON/OFFswitch on the control panel to position I.
5. Using the control thermostat (7.5 "
Control
thermostat"), set the desired water temperature.
If there is a heat demand, the appliance will run
through the heating cycle (9.3 "
The appliance's
heating cycle").
9.3 The appliance's heating cycle
The appliance's heating cycle is activated as soon as
the measured water temperature
(Twater
) falls below
the threshold value (T
set
). This threshold value
depends on the currently selected appliance operating
mode. For example, if the appliance is in OFF mode
(frost protection), then this value is 20 °C. If the
appliance is in ON mode, for example, then this
threshold value can be selected, e.g. position 3
(± 60 °C).
The heating cycle runs successively through the
following states:
1. HEAT DEMAND;
2. WAIT;
3. PRE-GLOW;
4. IGNITION;
5. RUNNING;
6. WAIT.
The entire cycle is explained in the example below.
Note
The cycle has the same steps when frost
protection is activated.
1. The control thermostat sensor measures the
temperature. The water temperature falls below
the set temperature of (for example) 60 °C,
causing the control thermostat to close. The burner
control now detects a demand and starts the
heating cycle.
2. Following demand, the wait period starts. This wait
ensures that the ignition is safe. The wait period
lasts approximately 15 seconds.
3. Once the wait period has elapsed (there is audible
‘clicking’ of the relay in the burner control), the
PRE-GLOW starts.
4. After about 12 seconds (pre)glowing, the gas
control valve opens and ignition takes place.
5. After ignition, the flame is detected and the
appliance will be running. This means that actual
heating has started.
6. When the water reaches the set temperature, the
demand ceases. The gas control valve closes and
the burner tray is extinguished. A new wait period
of about 10 seconds starts.
7. At the end of this wait, the appliance enters the idle
state, and waits until the water temperature once
more falls below the set temperature.
With any subsequent heat demand, the heating cycle
will resume from step 1.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith BFM100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith BFM100 in the language / languages: English as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith BFM100

A.O. Smith BFM100 User Manual - German - 70 pages

A.O. Smith BFM100 User Manual - Dutch - 70 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info