503219
36
Zoom out
Zoom in
Previous page
1/100
Next page
Installation
36 Instruction manual BFC
3
is
3.10.5 Connecting a program-controlled pump
Note
The maximum power capacity for a pump regulated by the controller
is 100W.
1. Connect neutral (N), live (L) and earth ( ) to terminals 13, 14 and 15 as
indicated in the table (3.10.2 "Preparation").
2. Fit the cable in the strain relief.
3. If you have no more connections to make:
- Fit the cover on the terminal block.
- Fit the covers onto the water heater.
3.10.6 Connecting an extra ON mode switch
External ON/OFF is an option for connecting an external ON/OFF switch. In
the OFF position, the programmed operating mode is active. In the ON
position, the programmed operating mode is overruled, and "ON mode" is
active.
1. Connect leads (X
3
and X
4
) to terminals 21 and 22 according to the
table (3.10.2 "Preparation").
2. Fit the cable in the strain relief.
3. If you have no more connections to make:
- Fit the cover on the terminal block.
- Fit the covers onto the water heater.
3.10.7 Connect additional error signal
The appliance has a relay terminal that is switched when an error is detected.
This can be used to signal errors, for example with a bulb. A 230V circuit can
be powered directly. Other voltages require a relay prescribed by the
manufacturer.
1. Connect the phase cables (X
1
and X
2
) to points 10 and 11 according to the
table (3.10.2 "Preparation"). If required, connect earth ( ) to terminal 12.
2. Fit the cable in the strain relief.
3. If you have no more connections to make:
- Fit the cover on the terminal block.
- Fit the covers onto the water heater.
3.11 Check the supply
pressure, gas
control valve
pressure, CO
2
value
and switching
pressure
Note
Before starting to use the appliance and/or checking the supply pressure
and/or the CO
2
value and/or the switching pressure, you should first
fill (5 "Filling") the appliance.
Caution
When starting up for the first time or after conversion, you must always
check the supply pressure, the gas control valve pressure, the CO
2
value and
the switching pressure.
Note
A CO
2
meter and a pressure gauge must be available for checking the
supply pressure, gas control valve pressure, CO
2
value and switching pressure.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith BFC80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith BFC80 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith BFC80

A.O. Smith BFC80 Usermanual and installation guide - German - 100 pages

A.O. Smith BFC80 User Manual - Dutch - 116 pages

A.O. Smith BFC80 Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info