503218
40
Zoom out
Zoom in
Previous page
1/100
Next page
Installation
40 Instruction manual BFC
3
is
Gas control valve pressure adjustment
3.11.3 CO
2
adjustment
To check the CO
2
value under full load and partial load and to adjust it if
necessary, proceed as follows:
1. Isolate (10.3 "
Isolating the water heater from the mains") the appliance from
the power supply.
2. Carefully remove the covers from the appliance.
3. The electrical section is now visible.
4. Place the CO
2
meter's measurement probe in the test nipple (58) of the flue
gas outlet pipe (the number is a reference on the General working principle
of the water heater).
5. Open the gas supply and vent the gas supply line.
6. Use the main switch to apply mains voltage to the appliance.
7. Start (9 "
Starting the water heater") the appliance.
8. Go to the :
SERVICE OPERATION
menu.
9. Generate a heat demand by draining the appliance until it is cold or by
raising the value for
Tset
in the
SERVICE
menu. Use for this.
Full-load measurement
10. From the service menu, select:
-
SERVICE OPERATION
|
FULL LOAD
- Confirm with .
The appliance is now in "FULL LOAD mode" and will ignite.
11. The appliance is now running at
FULL LOAD
. Read the value from the CO
2
meter and wait until this measured value has remained stable for some time.
This may take several minutes.
12. Then compare the measured CO
2
value against the value from the
table (3.4.3 "
Gas data").
Caution
The CO
2
value at full load must be within ±1.0 vol% of the CO
2
value stated
in the table (3.4.3 "Gas data").
IMD-1096b R0
SERVICE Ê Ê
FULL LOAD 65ÉC
Tset 70ÉC
RUNNING
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith BFC60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith BFC60 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith BFC60

A.O. Smith BFC60 Usermanual and installation guide - German - 100 pages

A.O. Smith BFC60 User Manual - Dutch - 116 pages

A.O. Smith BFC60 Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info