503220
79
Zoom out
Zoom in
Previous page
1/100
Next page
is
Instruction manual BFC 79
F06 (blocking error)
Short circuit between
flame probe and earth
Damaged cable in
contact with metal
surface or bent flame
probe.
Check the wiring and the flame probe. Replace the wiring and/or
flame probe if necessary.
If the error persists, contact your installation engineer.
To replace the necessary parts, you must contact your installation
engineer
Ceramic part of the
flame probe is
broken/cracked.
1. Check whether the ceramic part of the flame probe is still intact,
in the vicinity of the air distribution plate of the burner.
2. If not the flame probe must be replaced.
F07 (lock out error)
A flame has been
detected after the gas
control valve was
closed.
Defective gas control
valves
1. Check whether there is still burner pressure present, after the
gas control valves have closed.
2. Check whether a flame is still present, after the gas control
valves have closed.
3. If this is the case, the gas control valve must be replaced.
If the error cannot be resolved or is persistent, contact your
installation engineer
To replace the necessary parts, you must contact your installation
engineer
F08 (lock out error)
Error message from
safety relay
Flame detection before
the gas control valve
opened.
1. Reset controller.
2. If the error appears again, replace the controller.
If the error cannot be resolved or is persistent, contact your
installation engineer
To replace the necessary parts, you must contact your installation
engineer
F09 (lock out error)
Water temperature
protection.
Temperature at the top
of the tank exceeds
93
o
C.
1. Check that the circulation pump (if present) is working
2. Check the position of temperature sensor T
1
3. Reset controller
If the error cannot be resolved or is persistent, contact your
installation engineer
F11 (blocking error)
Flame detection with
closed gas control
valve.
Defective gas control
valves
See F07.
F19 (blocking error)
Power supply voltage is
too low.
There is not enough
supply voltage.
1. Check that there is power to the controller
2. The measured voltage must be 230 V
AC (-15%, +10%)
See the electrical diagram (17 "
Appendices").
If the error persists, consult your installation engineer
Code + description Cause Measure Remark
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith BFC100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith BFC100 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith BFC100

A.O. Smith BFC100 Usermanual and installation guide - German - 100 pages

A.O. Smith BFC100 User Manual - Dutch - 116 pages

A.O. Smith BFC100 Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info