813872
26
Zoom out
Zoom in
Previous page
1/30
Next page
1. Wall
2. Insulation layer (chimney flue)
3. Connection / chimney flue
4. Insulation layer (rear wall)
5. Convection area
6. Grid for the inflow of convection air
7. Concrete slab min. 6 cm (for installation
aprotective ceiling)
8. Ceiling
9. Insulation layer (floor)
10. Air supply to the fireplace
11. Surroundings (of the room)
12. Insulation layer (ceiling)
13. Grid for extraction of convection air
14. Protective floor made from fireproof
material
15. Insulation layer (sides)
16. Surroundings (of the room)
17. Radiation area
18. Flammable material
19. Ventilated radiation protection
20. Protective wall
21. Fire protection on the passage through
theflue channel
22. Firewall from mineral material
23. Furniture for flammable materials at
adistance of min 5 cm from the wall of
thesurroundings
Convection area
- If the hot-air jacket is not used, then between the fireplace insert and the insulation layer (4, 15)
there must be a minimum gap of 6 cm on the rear and side areas.
- The convection area must be insulated from all walls with the exception of walls which form the
heat-exchange area of the surroundings.
- The walls, floor and ceiling of the convection area must be clean and resistant to the abrasion.
Flow of convection air from the hot-air jacket
- All hot convectional piping must consist of form stable non-flammable materials.
- When installing a hot-air jacket, the hose for the flow of hot air must be firmly connected
totheflange of the hot-air jacket and to the input grid.
Operation of the air grid (hypocaust)
- The conventional air circulates in the closed shelling. The heat from the convectional area is
transferred into the room through the heat-exchange areas of the surroundings.
- The heat load in the convectional area of the hypocaust is higher than that for the construction
with air grids. This higher heat load must be taken into account for additional insulation of the
conventional space.
- The size and the construction of the heat-exchange area of the surroundings must correspond
to the heat output of the insert.
Forewall (protection of walls from flammable materials)
- This is used to protect the walls of the building (20) and consists of mineral material with a
minimum thickness of 10 cm.
- The pre-wall may be terminated a minimum of 20 cm above the chimney flue (3).
- The forewall is not required to be built when the wall of the building:
- is at least 10 cm thick
- is constructed from non-flammable materials
- is not a load-bearing concrete wall or a reinforced concrete wall
26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.Caminetti Quattro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.Caminetti Quattro in the language / languages: English as an attachment in your email.

The manual is 16.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info