654565
10
Zoom out
Zoom in
Previous page
1/24
Next page
10 © 3M 2012. All rights reserved.
ENGLISH
3M™ Digital Projector X21i/X26i Product Warranty and Safety Guide
Important Note
1. To avoid premature lamp failure, do not change the mounting position of the
projector (desktop ceiling mount or ceiling desktop mount) and continue to use the
same lamp.
2. To avoid reduced lamp life, do not touch projection lamp with bare ngers.
3. To avoid reduced image quality, do not touch projection lens or other internal
optical components.
4. Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other
than those referred to in the “Operator's Guide”.
5. For maximum lamp life, do not strike or drop, improperly handle, or scratch the
lamp glass. Also, do not install an old or used lamp.
6. Keep air lter clean. Refer to the cleaning instructions contained in the “Operator’s
Guide”.
7. Keep all ventilation openings free of any obstructions.
8. In some countries, the line voltage is NOT stable. This projector is designed to
operate safely within a bandwidth of 100 to 120 volts / 220 to 240 volts (50 to 60
Hz) ±10%, but could fail if power drops or surges of ±10 volts occur. In these high-
risk areas, it is recommended to install a power stabilizer unit.
9. Do not block intake or exhaust air vents. This will cause the projector to over heat
and shut down.
10. Do not place the projector in direct sunlight or near a hot object such as a heater.
11. To prevent damaging the projector, always hold the projector whenever using the
elevator buttons to adjust the elevator feet.
12. Use the accessory cable or a designated-type cable for the connection. Some
cables have to be used with core set. A too long cable may cause certain picture
degradation. Please consult with your dealer for details. For cables that have a
core only at one end, connect the core to the projector.
13. Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
14. Do not place the projector in the side/front/rear-up position, except care of the air
lter.
15. The mark is in compliance with the Waste Electrical and Electronic Equipment
Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT
to dispose the equipment including any spent or discarded batteries
or accumulators as unsorted municipal waste, but use the return and
collection systems available. If the batteries or accumulators included with
this equipment, display the chemical symbol Hg, Cd, or Pb, then it means
that the battery has a heavy metal content of more than 0.0005% Mercury or more
than, 0.002% Cadmium, or more than 0.004% Lead.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m X21i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m X21i in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info