5609
6
Zoom out
Zoom in
Previous page
1/11
Next page
5
Requesting projector status (Get command)
(1) Send the request code Header + Command data (02H+00H+ type (2 bytes)
+00H+00H) from the computer to the projector.
(2) The projector returns the response code 1DH+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (01H+00H+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code 06H to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (06H+00H+
type (2 bytes) +00H+00H) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code 06H to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (04H+00H+
type (2 bytes) +00H+00H) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code 06H to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (05H+00H+
type (2 bytes) +00H + 00H) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code 06H to the computer.
When the projector cannot understand the received command
When the projector cannot understand the received command, the error code 15H is
sent back to the computer.
Sometimes the projector cannot properly receive the command. In such a case, the
command is not executed and the error code 15H is sent back to the computer. If this
error code is returned, send the same command again.
When the projector cannot execute the received command.
When the projector cannot execute the received command, the error code 1cH +
xxxxH is sent back to the computer. When the data length is greater than indicated by
the data length code, the projector ignore the excess data code.
Conversely when the data length is shorter than indicated by the data length code, an
error code will be returned to the computer.
Operation cannot be guaranteed when the projector receives an
undefined command or data.
Provide an interval of at least 40ms between the response code and any other code.
The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
Commands are not accepted during warm-up.
NOTE
S40/X40-TECH 03.8.21 3:50 PM ページ 5
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m S40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m S40 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m S40

3m S40 User Manual - German - 40 pages

3m S40 User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info