5585
32
Zoom out
Zoom in
Previous page
1/41
Next page
31
The LAMP indicator is also red when the lamp unit reaches high temperature.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power
ON again. If the LAMP indicator is still red, replace the lamp.
NOTE
Replacing the lamp
All projector lamps will wear out eventually. If used for long periods of time, the image could become
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps
early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up
the projector, the lamp needs to be replaced. (See "Related Messages" ( ) and "Regarding the
Indicator Lamps" ( ) for details.)
1
witch the projector OFF,
remove the power cord from
the power outlet, and wait at
least 45 minutes for the unit
to cool.
5
Loosen the three screws, and
gently remove the lamp while
holding the grips. Touching
the inside of the lamp case
may result in uneven coloring.
6
Install the new lamp and
tighten the three screws
firmly. Also steadily push the
opposite side of the screwed
lamp into the unit.
7
Replace the lamp cover in
position and tighten the two
screws firmly.
2
Prepare a new lamp.
3
Check that the projector has
cooled sufficiently, and gently
turn it upside down.
4
Loosen the two screws as
shown in the diagram, and
remove the lamp cover.
ATTENTION
Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
Do not use with lamp cover removed.
Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing
the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER
WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following
operation within 10 minutes of switching power ON.
8
Gently turn the projector right-
side up.
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 26
5
6
3
3
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8749 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8749 in the language / languages: English as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8749

3m MP8749 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info