5571
25
Zoom out
Zoom in
Previous page
1/38
Next page
ENGLISH
23
E 3M 1997
3Mt
Multimedia Projector MP8660
Section 8: Troubleshooting
The MP8660 has been designed to be as simple and trouble-free to use as possible. If you should run into
problems operating the projector, please review the troubleshooting information below.
Problem Probable Causes Solution
Power does not come on
Power not connected.
Rear cover is open.
Plug power cord into an electric
outlet.Turn power switch to “ON.”
Close cover door tightly.
No picture and sound
Input connections not properly
installed.
Set the projector to the correct
input source.Check all cable
connections from input source to
projector.Make sure the input
source power is on.
Picture displays but no sound
Cable connections loose and/or
volume adjustment needed.
Check all cable connections from
input source to projector.Press
VOLUME then + on the remote
control.Press the MUTE button on
the remote control.
Sound but no picture
Cable connections loose and/or
picture adjustment needed.
BLANK button has been pressed.
Check all cable connections from
input source to projector. Adjust
the picture brightness. Press
MENU, then press SELECT.
Press BLANK button to restore
picture.
Weak saturation
Picture adjustment needed. Adjust picture color and tint (video
only). Press MENU, then press
SELECT.
Picture is dark
Picture adjustment needed Adjust the picture brightness and
contrast. Press MENU, then press
SELECT.Lamp may need
replacement. Call customer
service for assistance. See
Service Information below.
Picture is not sharp and clear
Picture adjustment needed. Adjust focus, H-size (RGB) and
phase. Press MENU, then press
SELECT.
WARNING is flashing on the
projection screen
Projector is overheating. Turn the projector off and let it cool
for 30 minutes. Clean the air filter
and check all ventilation holes for
blockage.
LAMP indicator red, Power-On
indicator amber
Problem with lamp has been
detected.
Turn the power off and let the
projector cool. If the LAMP
indicator comes on again, replace
the lamp. If problem continues,
call service.
“Change Lamp” message
displays when projector is
powered on
Lamp has been used for
recommended 1000 hours.
The Change Lamp message will
display for 30 seconds after power
on when the lamp clock reaches
1000 hours. This lamp is old and
should be replaced.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8660 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8660 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8660

3m MP8660 User Manual - German - 26 pages

3m MP8660 User Manual - Dutch - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info