5553
18
Zoom out
Zoom in
Previous page
1/28
Next page
16
3M Multimedia Projector MP8020
1996
When the projector is displaying a video or computer image, press the H/V button to switch to the
MENU mode and the LED will begin flashing. Move the trackball left/right to adjust the image
horizontally or up/down to adjust the image vertically. When changes are complete, press the H/V
button to return to the NORMAL mode.
Note
The LED will stop flashing and return the remote control transmitter to the NORMAL mode
after five seconds of inactivity.
Sizes the picture to fit the screen. Press
to make the projected image wider or to reduce the
image size.
Press
or to focus the image.
Turn the audio (speaker) sound ON (mute bar turns green) or OFF (mute bar turns red).
This button displays a digital countdown clock in the upper left corner of the
projection screen. Minutes are displayed on the left and seconds on the right.
You can set the timer for the desired number of minutes to be counted down.
Seconds cannot be set – they are a display only field.
When the projector is in the Normal mode:
a. Press TIMER to display the clock. Figure 52.
b. Press the RESET button to position the cursor in the left most minutes column.
c. Press and hold RESET to put the remote in menu mode (LED will flash).
d. Move the track ball up/down to change the digit.
e. Move the track ball left/right to move to the next column.
f. Press RESET to start the clock.
To reset the clock for a different amount of time, repeat steps b-f. To remove the clock display from
the projection screen, press TIMER.
Press to blank the screen (screen turns blue). Press again to return the normal display.
Press
to decrease or to increase the speaker volume (NORMAL mode) or to move
left/down or
to move right/up to adjust the setting of an on-screen menu line. See MENU
button.
The menu button is used to switch the projector and remote control between the NORMAL (Video
image and LED is Off) and MENU (On-screen Menu and LED is flashing) operating modes.
NORMAL Mode
: (Video image being displayed, LED is Off) The normal operating mode is used to
display normal video images from your video or computer sources. Use the remote control buttons
to adjust the focus and volume levels of the projector and operate the mouse key functions (trackball,
drag, left/right) to control the video presentation.
MENU Mode
: (On-screen Menu being displayed, LED is FLASHING) The MENU operating mode
is used to display on-screen Menus. These menus allow you to adjust the MP8020 projector settings
for best performance.
To make a projector setting change from the on-screen menu:
a. Press and release the MENU button to display the onscreen menu.
b. Press and hold the MENU button for two seconds to change the remote to the MENU
mode. The LED on the remote will flash the entire time the remote is in the menu mode.
c. Move the trackball to make the desired changes on each Menu line.
d. Press the Menu button to return to the NORMAL mode.
e. Wait five seconds for the LED to stop flashing - remote automatically returns to Normal
mode.
H/V
←→
00:00
Minutes : Seconds
Clock Display
Figure 5-2. Clock
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8020 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8020

3m MP8020 User Manual - German - 22 pages

3m MP8020 User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info