534678

3Dprintingsystems UP Plus Manual

52
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
8.4 How to clean the extruder column
•
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
ment from the extruder head.
• Remove the nozzle.
•
Click “Withdraw” again, when the printer beeps.
•
Using the gloves and a 1
silver column of the extruder column removing any plastic residue.
•
Clean the plastic off the drill bit each time.
•
You might need to click “Withdraw” a few times to remove as much plastic residue as
possible.
8.5
How to clean the extruder drive gear
head)
•
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
ment from the extruder head.
•
Switch off at the back of the printer and wait for the extruder to cool down.
•
Remove all the connector plugs at the top of the extruder.
Figure a.)
• Remove the
extruder head from the printer
two Alan screws from above the fan that hold the white plastic onto the stepper motor, as
indic
ated with red arrows in (figure b)
•
Pull the plastic part away from the stepper mot
• Place
the Alan key under the drive gear cover (figure
brush clean the plastic dust residue that is inside the drive gear.
•
Replace the drive gear cover and replace the plastic cover.
Note: There ar
e a few different variations of extruder heads, but removal is similar.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
8.4 How to clean the extruder column
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
ment from the extruder head.
Click “Withdraw” again, when the printer beeps.
Using the gloves and a 1
–
1.5mm drill bit and using your hand twist and poke up into the
silver column of the extruder column removing any plastic residue.
Clean the plastic off the drill bit each time.
You might need to click “Withdraw” a few times to remove as much plastic residue as
How to clean the extruder drive gear
(v2 extruder
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
ment from the extruder head.
Switch off at the back of the printer and wait for the extruder to cool down.
Remove all the connector plugs at the top of the extruder.
(figure a)
Figure b.)
Figure b.)
extruder head from the printer
using the large supplied Alan key
two Alan screws from above the fan that hold the white plastic onto the stepper motor, as
ated with red arrows in (figure b)
.
Pull the plastic part away from the stepper mot
or and lay to one side
the Alan key under the drive gear cover (figure
c) and lever
the cover off. Using a
brush clean the plastic dust residue that is inside the drive gear.
Replace the drive gear cover and replace the plastic cover.
e a few different variations of extruder heads, but removal is similar.
Troubleshooting
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
a-
1.5mm drill bit and using your hand twist and poke up into the
You might need to click “Withdraw” a few times to remove as much plastic residue as
(v2 extruder
First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil
a-
Switch off at the back of the printer and wait for the extruder to cool down.
Figure b.)
using the large supplied Alan key
. Remove the
two Alan screws from above the fan that hold the white plastic onto the stepper motor, as
the cover off. Using a
e a few different variations of extruder heads, but removal is similar.
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info